Filter
Top Products
RL78/G1A CHAPTER 6 TIMER ARRAY UNIT
R01UH0305EJ0200 Rev.2.00 202
Jul 04, 2013
Figure 6-11. Format of Timer Mode Register mn (TMRmn) (1/4)
Address: F0190H, F0191H (TMR00) to F019EH, F019FH (TMR07) After reset: 0000H R/W
Symbol 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
TMRmn
(n = 2, 4, 6 )
CKS
mn1
CKS
mn0
0
CCS
mn
MAST
ERmn
STS
mn2
STS
mn1
STS
mn0
CIS
mn1
CIS
mn0
0 0
MD
mn3
MD
mn2
MD
mn1
MD
mn0
Symbol 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
TMRmn
(n = 1, 3)
CKS
mn1
CKS
mn0
0
CCS
mn
SPLIT
mn
STS
mn2
STS
mn1
STS
mn0
CIS
mn1
CIS
mn0
0 0
MD
mn3
MD
mn2
MD
mn1
MD
mn0
Symbol 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
TMRmn
(n = 0, 5, 7)
CKS
mn1
CKS
mn0
0
CCS
mn
0
Note
STS
mn2
STS
mn1
STS
mn0
CIS
mn1
CIS
mn0
0 0
MD
mn3
MD
mn2
MD
mn1
MD
mn0
CKS
mn1
CKS
mn0
Selection of operation clock (f
MCK) of channel n
0 0 Operation clock CKm0 set by timer clock select register m (TPSm)
0 1 Operation clock CKm2 set by timer clock select register m (TPSm)
1 0 Operation clock CKm1 set by timer clock select register m (TPSm)
1 1 Operation clock CKm3 set by timer clock select register m (TPSm)
Operation clock (fMCK ) is used by the edge detector. A count clock (fTCLK) and a sampling clock are generated
depending on the setting of the CCSmn bit.
The operation clocks CKm2 and CKm3 can only be selected for channels 1 and 3.
CCS
mn
Selection of count clock (f
TCLK) of channel n
0 Operation clock (fMCK) specified by the CKSmn0 and CKSmn1 bits
1 Valid edge of input signal input from the TImn pin
In channel 5, Valid edge of input signal selected by TIS0
Count clock (fTCLK) is used for the timer/counter, output controller, and interrupt controller.
Note Bit 11 is fixed at 0 of read only, write is ignored.
Cautions 1. Be sure to clear bits 13, 5, and 4 to “0”.
2. The timer array unit must be stopped (TTm = 00FFH) if the clock selected for f
CLK is changed
(by changing the value of the system clock control register (CKC)), even if the operating clock
specified by using the CKSmn0 and CKSmn1 bits (f
MCK) or the valid edge of the signal input
from the TImn pin is selected as the count clock (f
TCLK).
Remark m: Unit number (m = 0), n: Channel number (n = 0 to 7 (however, timer input pin (TImn), timer output pin
(TOmn) : n = 0, 1, 3 to 7))