Filter
Top Products
Administrator Level Options
3-17 41-001343-02 REV04 – 05.2014
XML Beep Support
Note:
This option can be set by both
Users and Administrators.
xml beep notification Enables or disables the playing of a beep to indicate a status on the phone. When the
phone receives a status message, the BEEP notifies the user that the message is dis-
playing.
For more information on this feature, see “XML Beep Support” on page5-62.
Status Scroll Delay (seconds)
Note:
This option can be set by both
Users and Administrators.
xml status scroll delay Allows you to set the time delay, in seconds, between the scrolling of each status
message on the phone.
For more information on this feature, see “Status Scroll Delay” on page5-63.
Switch UI Focus to Ringing
Line
Note:
This option can be set by both
Users and Administrators.
switch focus to ringing line Enables or disables whether or not the UI focus is switched to a ringing line while the
phone is in the connected state.
For more information on this feature, see “Switch Focus to Ringing Line” on page5-
64.
Call Hold Reminder During
Active Calls
Note:
This option can be set by both
Users and Administrators.
call hold reminder during
active calls
Enables or disables the ability for the phone to initiate a continuous reminder tone
on the active call when another call is on hold. When this feature is disabled, a ring
splash is heard when the active call hangs up and there is still a call on hold.
For more information on this feature, see “Call Hold Reminder During Active Calls” on
page5-65.
Call Hold Reminder
Note:
This option can be set by both
Users and Administrators.
call hold reminder Enables or disables the reminder ring splash timer to start as soon as you put a call on
hold (even when no other calls are active on the phone). When enabled, the phone
initiates a reminder ring splash periodically for the single call on hold. When disabled,
no reminder ring splash is audible.
For more information on this feature, see “Call Hold Reminder (on Single Hold)” on
page5-66.
call hold reminder timer
Note:
This option can be set by an
Administrator only.
Specifies the time delay, in seconds, that a ring splash is heard on an active call when
another call was placed on hold. For example, if a call comes into Line 1, and then a
call comes into Line 2 and you answer Line 2, Line 1 is automatically placed on hold.
While on the active Line 2, after 7 seconds, a ring splash audio sounds on the line
reminding you that the call on Line 1 is still on hold. This timer begins to increment
after Line 2 is answered.
Notes:
• This parameter is used with the “call hold reminder frequency” parameter.
• You must enable this “call hold reminder timer” parameter for it to work.
• A value of “0” disables the call hold reminder feature.
For more information on this feature, see “Call Hold Reminder Timer & Frequency” on
page5-67.
call hold reminder frequency
Note:
This option can be set by an
Administrator only.
Specifies the time interval, in seconds, between each ring splash sound on the active
line. For example, if a call comes into Line 1, and then a call comes into Line 2 and you
answer Line 2, Line 1 is automatically placed on hold. While on the active Line 2, after
7 seconds, a ring splash audio sounds on the line reminding you that the call on Line
1 is still on ho
ld (determined by the “call hold reminder timer” parameter), and then
the ring splash is heard again after 60 seconds (determined by this parameter).
Notes:
• You must enable the “call hold reminder” and/or “call hold reminder during active
calls” parameter(s), and the “call hold reminder timer” parameter, for this parameter
to work.
• A value of “0” prevents additional rings.
For more information on this feature, see “Call Hold Reminder Timer & Frequency” on
page5-67.
Parameter in
Aastra Web UI
Parameter in Configuration
Files
Description