Renesas rl78 Answering Machine User Manual


  Open as PDF
of 1004
 
RL78/G1A CHAPTER 16 INTERRUPT FUNCTIONS
Table 16-2. Flags Corresponding to Interrupt Request Sources (2/4)
Interrupt Request Flag Interrupt Mask Flag Priority Specification Flag Interrupt
Source
Register Register Register
64-pin
48-pin
32-pin
25-pin
INTST2
Note 1
STIF2
Note 1
STMK2
Note 1
STPR02, STPR12
Note 1
INTCSI20
Note 1
CSIIF20
Note 1
CSIMK20
Note 1
CSIPR020, CSIPR120
Note 1
INTIIC20
Note 1
IICIF20
Note 1
IICMK20
Note 1
IICPR020, IICPR120
Note 1
INTSR2
Note 2
SRIF2
Note 2
SRMK2
Note 2
SRPR02, SRPR12
Note 2
INTCSI21
Note 2
CSIIF21
Note 2
CSIMK21
Note 2
CSIPR021, CSIPR121
Note 2
INTIIC21
Note 2
IICIF21
Note 2
IICMK21
Note 2
IICPR021, IICPR121
Note 2
INTSRE2 SREIF2 SREMK2 SREPR02, SREPR12
INTDMA0 DMAIF0 DMAMK0 DMAPR00, DMAPR10
INTDMA1 DMAIF1 DMAMK1 DMAPR01, DMAPR11
INTST0
Note 3
STIF0
Note 3
STMK0
Note 3
STPR00, STPR10
Note 3
INTCSI00
Note 3
CSIIF00
Note 3
CSIMK00
Note 3
CSIPR000, CSIPR100
Note 3
INTIIC00
Note 3
IICIF00
Note 3
IICMK00
Note 3
IICPR000, IICPR100
Note 3
INTSR0
Note 4
SRIF0
Note 4
SRMK0
Note 4
SRPR00, SRPR10
Note 4
INTCSI01
Note 4
CSIIF01
Note 4
CSIMK01
Note 4
CSIPR001, CSIPR101
Note 4
INTIIC01
Note 4
IICIF01
Note 4
IICMK01
Note 4
IICPR001, IICPR101
Note 4
INTSRE0
Note 5
SREIF0
Note 5
SREMK0
Note 5
SREPR00, SREPR10
Note 5
INTTM01H
Note 5
TMIF01H
Note 5
IF0H
TMMK01H
Note 5
MK0H
TMPR001H,
TMPR101H
Note 5
PR00H,
PR10H
Notes 1. If one of the interrupt sources INTST2, INTCSI20, and INTIIC20 is generated, bit 0 of the IF0H register is set
to 1. Bit 0 of the MK0H, PR00H, and PR10H registers can be used for all three of these interrupt sources.
2. If one of the interrupt sources INTSR2, INTCSI21, and INTIIC21 is generated, bit 1 of the IF0H register is set
to 1. Bit 1 of the MK0H, PR00H, and PR10H registers can be used for all three of these interrupt sources.
3. If one of the interrupt sources INTST0, INTCSI00, and INTIIC00 is generated, bit 5 of the IF0H register is set
to 1. Bit 5 of the MK0H, PR00H, and PR10H registers can be used for all three of these interrupt sources.
4. If one of the interrupt sources INTSR0, INTCSI01, and INTIIC01 is generated, bit 6 of the IF0H register is set
to 1. Bit 6 of the MK0H, PR00H, and PR10H registers can be used for all three of these interrupt sources.
5. Do not use the error interrupt of UART0 reception and the interrupt of channel 1 of TAU0 (while the higher 8
bits are operating at a timer) at the same time because they share flags for the interrupt request sources. If
the error interrupt of UART0 reception is not used (EOC01 = 0), UART0 and channel 1 of TAU0 (while the
higher 8 bits are operating at a timer) can be used at the same time. If the interrupt source INTSRE0 or
INTTM01H is generated, bit 7 of the IF0H register is set to 1. Bit 7 of the MK0H, PR00H, and PR10H
registers can be used for both these interrupt sources.
R01UH0305EJ0200 Rev.2.00 695
Jul 04, 2013