Filter
Top Products
PROGRAMMINGPROCEDURES-INSTRUCTIONS/SYSTEMRECORDS
SECTION 200-096-302
FEBRUARY1991
PROGRAM10-2
SYSTEMASSIGNMENTS,PART2OF2
SELECT = 2 Key L EL&
Light LEDs as defined by the table below.
ALL LEDs with an “x” should be lit when you finish
BUTTON/LED 1 X 1
LED On
I
LED Off
20
19”
1R
-
-
Station External Amp Conference
No External Amplifier Connected
Two CO Line Conference No Two CO Line Conference
17
I I
16
2
Executive Override Warning Tone/ON Executive Override Warning Tone/OFF
157
2 External Page included with All Call Page Not Included
14
2
Privacy Override Warning Tone/ON Privacy Override Warning Tone/OFF
13
Send Auto Callback Camp-on Tone 3
No Callback Tone
I
12
CO Line 3 min Beep Tone
No Beep Tone
(R2) 11
No DTMF Tone Returns DTMF Tone Return
(R2) lo4
BGM connected to PESU, Circuit 81°
EKT connected to PESU, CKT 8
(R2) 09 4
BGM connected to PEKU, Circuit 3” EKT connected to PEKU, CKT 3
08
Display Dialed Number/l min.
Display Dialed Number/l 5 sec.
(R2) 076
I I
Standard Tel. CO Ring
per Prog. 1 O-l, LED 06
Standard Tel. CO Ring Distinctive
(R2) 06 5
VM ID Code DTMF Signal Time 80 ms
160 ms
(R3) 05
TIE/DISA Busy Tone, 0.5 second cadence9 TIE/DISA Busy Tone, 0.25 second cadence
(R2) 04
MW cancel from VM; dial 1 I& Station No.
MW cancel from VM: Automatic
03
I I
Ringing Modes/3
I
Ringing Modes/2
02
2 Hunt/C.F. override from console’s phone
Hunt/C.F. override from console
01
Tone First (from DSS Console)
Voice First (from DSS Console)
NOTES:
1. For more information, see the instructions preceding the record sheets.
2.
Initialized data lights LEDs 02, 14, 15 and 16.
3. Called party receives notification tone when calling party activates ACB.
4. BGM connected to PEKU, Circuit 3 or PEW, Circuit 8 will be sent to electronic
(optional).
5. VM ID code DTMF signal time is fixed at 160 msec for Release 1 software.
and digital telephone speakers and external page
6. The ring pattern for standard telephone, distinctive ring on incoming CO calls is: 0.2 sec. on/O.4 sec. off, 0.2 sec. on/O.4 sec. off, 3 sec.
off; intercom ring is always 1 sec. on, 3 sec. off. This does not apply to VM Ports (Program 31, LED 17 on) which are always standard
7. g%rna/ speakers and a// electronic and digital telephones are paged by dia/ing:miB
Them key is used to page a// electronic telephones
Only;
external speakers are not included when using the a key.
8. Deletes DTMF tones returned to electronic telephones when dialing from dialpad or speed dialing; also deletes auto dial digits from
callers that are call forwarded to voice mail. This does not affect the actual DTMF tones sent out to the CO or voice mail.
9. 0.5 second cadence, Bell Standard Busy Tone, should be enabled so outside callers are not confused by STRATA 0.25 second busy
tone when calling busy number on DISA and TIE line calls
IO.
PESUPEKU must be in SLOT 01 if using Release 2 software; PESLUPEKU can be in any universal slot assigned in Program 79-7 if
using Release 3 software.
Il. Important: LED 19 should be OFF unless external amplifiers are used for two-CO line/station conference (see Program 10-3). If LED 19
is ON, the station may be unbalanced and receive HUM if external amplifier with Auto-Gain-Control is not connected.
2-54