Filter
Top Products
INSTALLATION-PERIPHERALS
SECTION 200-096-208
FEBRUARY1991
messaging systems. Depending on the voice mail
system used, some of the features available with
INTOUCH (refer to Paragraph
9.10)
may be avail-
able
with the customer-supplied system.
9.22 Voice Mail (PSTU or PESU Port) Program-
ming Considerations
9.23 Voice mail (all types) PSTU or PESU port
programming is accomplished using
Programs 31
and
IO-2
(refer to Programming Procedures, Sec-
tion 200-096-300, for details). Voice mail (VM) pro-
gramming features are:
l
VM Groups-This
feature groups VM PSTU or
PESU ports together so that message waiting
set/cancel signals appear to originate from the
lowest port in the VM group. All VM ports con-
nected to a particular VM machine should
be set
in the same VM group
(Program 31,
LEDs 05 N
08).
l
Message Waiting
Set/Cancel-If the VM ma-
chine has the ability to dial a code, plus the
appropriate station numbers to set or cancel the
message waiting LEDs on electronic telephones,
program the VM machine to dial the following
sequences
(Program 10-2,
LED 04):
1) To set a MW LED, the VM machine must
dial Ii+ station number.
2) To cancel a MW LED, the VM machine
must dial Ii+ station number.
NOTE:
Only dial codes 63 and 64 are set in the VM
device configuration; the VM device will dial
the station number automatically to set/cancel
the MW LED.
l
No Conference
VM-Prevents undesired
three-party connections during VM call trans-
fers. All VM ports should be set for No Conf
(Program 31,
LED 09).
l
Privacy Override
Deny-Prevents stations from
overriding (breaking in) in-progress VM calls
(Program 31,
LED 18).
l
End-to-End
Signaling-Allows VM port
DTMF operation. All VM ports should be set for
end-to-end signaling
(Program 31,
LED 17).
NOTE:
The CRCU (-4 or -8) must be installed on the
PCTU or PCTUSI to allow End-to-End Sig-
naling.
. .
Receive Auto Call Forward ID
Codes-Pro-
vides auto digits from call forwarded stations to
direct callers to stations’ mailboxes. All VM ports
should be
set to
re,ceive
auto
ID code
(Program
31, LED 16).
9.24 Voice Mail Program Checklist.
The follow-
ing items should be verified before programming
voice mail:
1) Set INTOUCH Maintenance Menu system
parameters to “D” = STRATA DK (see
INTOUCH installation and Maintenance
Manual for other parameter settings).
2) STRATA DK programs:
Program
95 Initialization clears voice mail
auto dial codes.
Program
03: Verify that a CRCU (-4 or -8) is
installed on the PCTU to allow the VM/AA to
send DTMF tones.
Program
04: Assigns station numbers to
VM/AA ports (initialized numbers recom-
mended).
Program
05: First digit of special codes 63
and 64 (initialized numbers recommended).
Program 1 O-l
: Set the system for voice first,
and program the VM/AA device to dial the
suffix as “1” after station numbers.
Program 10-2:
Set LEDs 04 for set/cancel
operation and 06 ON for the VM to detect 80
msec. tones.
Program 13:
If the VM/AA device is the
message center, set the lowest VM port as
the message center.
Program 31:
Turn LEDs 05,09, and 15 N 20
ON for the PESU or PSTU ports that are
connected to the INTOUCH VM/AA ports.
Do not set these options for standard tele-
phone or electronic telephone station ports.
NOTE:
A, D, and B tones should be enabled only for
VM/AA devices that respond to these tones.
l
Program
33: Set the PESU and PSTU ports
that are connected to the VM/AA ports
8-16