Filter
Top Products
PROGRAMMINGPROCEDURES-INSTRUCTIONS/SYSTEMRECORDS
SECTION 200-096-302
FEBRUARY1991
should have the following LEDs turned ON: 04,
05, 09, 15,
16, 17, 18, 19, 20. These LED’s
should be set ON for VM ports only, not for
telephone ports.
NOTE:
LED 04 may be ON or OFF, depending on
VM/AA device operation. See the LED 04
write up that follows.
l
INTOUCH (B + Station Number), LED
20-This feature is associated with an
INTOUCH Digital Voice Messaging Sys-
tem connected to a PSTU or PESU port.
DTMF “B” tone followed by the station
number is sent to INTOUCH in situations in
which INTOUCH would not normally know
the location from which a call was coming,
such as hold recall or blind ring transfer
recall. This allows INTOUCH to respond
more intelligently with appropriate voice
prompts. This LED should be lit for PSTU
or PESU ports connected to VM devices
only, not for station ports connected to
telephones.
NOTES:
1. INTOUCH (B No Station) mustbe enabled
to allow this function.
2. This is available only with INTOUCH soft-
ware Release B.06 and above.
l
INTOUCH (B No Station), LED 19-DTMF
“B” tone is sent to INTOUCH to signify
a recall situation where INTOUCH
already knows the recalling station num-
ber. Again, thisallows INTOUCH to respond
more intelligently with appropriate voice
prompts. This LED should be lit for PSTU
or PESU ports connected to VM devices
only, not for station ports connected to
telephones.
NOTE:
This is available only with INTOUCH software
Release B.06 and above.
l
Executive and Privacy Override Block-
ing (Modem), LED 18-This feature de-
nies any other station to break in with
Privacy or Executive Override to the called
station’s connection. It should be‘used for
PSTU and PESU ports connected to a
modem or Voice Mail/Auto Attendant in
order to ensure data and voice security at
that port. This feature may also be used to
deny override of any station.
NOTE:
1. Themmbuttonmaybeusedto
disable privacy blocking on a call-by-call
basis; this button cannot disable execu-
tive override blocking.
2. If a modem is assigned to the system
modem pool in Program 21, use this op-
tion to provide data security (LED 18 ON
for modem PSTU ports assigned in Pro-
gram 21).
3. If using the system modem pool for data
calls that must be switched between voice
and data, LED 18 should be OFF for the
modem PSTUportsassignedin Program21.
l
End/End Signal RCV (VM), LED 17-
Activation of this option allows End to End
Signaling of DTMF tones through the sys-
tem. It is required on all Voice Mail-PSTUI
PESU ports in order to have proper signal-
ing communication.
l
Receive VM ID Code, LED 16-When a
station is call forwarded to a voice mail
system, certain Identification (ID) DTMF
tones will automatically be sent to direct
the call to a specific mailbox (VM ID Code
656). The automatic ID is also sent to the
voice mail device when electronic or digital
telephone users retrieve messages via the
Intercom and Message Waiting buttons
(VM ID Code 657). The voice mail port
must be programmed for this feature to
allow the receiving of DTMF digits.
@ INTOUCH Integration (A/D), LED 15-
This option will cause an answer tone
(DTMF “A”tone) to be automatically sent to
INTOUCH when a station answers, and a
disconnect tone (DTMF “D” tone) when a
station disconnects. This al-lows INTOUCH
to respond quickly rather than waiting a
2-12