Toshiba DK96 Telephone User Manual


 
NOTE:
An optional security code for DISA outgoing
CO calls is available via Program 60-6.
l
Ring IMDU Maintenance Modem, Fea-
ture
5-IMDU Remote Maintenance mo-
dem can be accomplished with this pro-
gram. Different alternatives are available
for the system modes of DAY, DAY2, and
NIGHT. If none of these are selected, the
IMDU can still be reached on station 19
with the DISCDISA feature or by a Ring
Transfer from the DSS console attendant
or any other station. IMDU station 19 must
be enabled with
Program 77-1.
Program 79-Door Phone Ringing:
o Muted Ring to Busy Electronic and
I
Digital Telephone, LED
20-If all elec-
tronic and digital telephones are busy, and
a door phone button is pressed, a muted
ring tone can be sent to selected digital and
electronic telephones, as defined with this
program (only the lowest port in the appro-
priate ringing group will mute ring).
l
Door Phone Ring, LEDs 01
w 12-When
a door phone button is pressed, selected
digital and/or electronic telephones will ring
as assigned with this program. See
Pro-
gram
77-2 description for an explanation
of the door phone A, B, and C numbering
scheme.
1 Program 80-Electronic and Digital Telephone
Ringing Tones:
Distinctive system ringing
sends a different ring tone for CO line ringing
than that for intercom ringing. In addition, CO
I
line ringing at electronic and digital telephones
can be different from one phone to another.
Two choices are available; one is 500 Hz
modulated with 640 Hz (PERCEPTION ring
tone), while the other is 600 Hz modulated with
800 Hz (STRATA ring tone). Two electronic or
I
digital telephones that are close in proximity
can then have distinctive CO line ringing, as
chosen with this program.
Programs 81
w 89-CO Line Ringing Assign-
ments:
A wide variety of CO line ringing to
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 200-096-302
FEBRUARY 1991
stations can be programmed into the system.
Nine categories exist, which are DAY IMMEDI-
ATE, DAY DELAY 1, DAY DELAY 2,‘DAY2
IMMEDIATE, DAY2 DELAY 1, DAY2 DELAY
2, NIGHT IMMEDIATE, NIGHT DELAY 1, and
NIGHT DELAY 2. DAY, DAY2 and NIGHT
refer to the three modes of the Night Transfer
key. DELAY 1 is a 12-second delay of ringing
signal to an electronic or digital telephone, and
DELAY 2 is a 24-second delay of ringing. The
delay functions are mainly used in CENTREX
applications but can be used for other situ-
ations. If delayed ringing occurs, the station
that initially rings will continue to ring with
subsequent delayed ring stations.
Program 93-CO Line Identification:
This pro-
vides alphanumeric names (to appear on LCD
telephones) to CO lines such as WATS BAND
5, FXTO NY, MR JONES, etc. The names may
be up to 16 alphanumeric characters each,
and display when the CO line is being used by
an LCD station.
Program 97-Printing Program Data Through
SMDR:
Contents of each program can be sent
to the SMDR port for a hard copy printout.
Setting Date, Time and Day:
The current date,
time, and day of the week can be set from the
electronic or digital telephone connected to
port 00 (usually station 200). These cannot be
set from the programming electronic or digital
telephone at port 05.
2 TOLL RESTRICTION
2.01 The following provides the programmer with
an overview of the Toll Restriction feature and
step-by-step instructions to fill in the Toll Restric-
tion System Record Sheets.
3 TOLL RESTRICTION OVERVIEW
3.00 Toll Restriction Methods
3.01
Toll Restriction screens and selectively
restricts outgoing calls using three different meth-
ods. Each type of restriction can be programmed
2-19