Filter
Top Products
contact’s PIOU relays
Kl
- K4 and the “C”
terminal of zone 1 - zone 4 speakers.
4) Connect the BGM music amplifier output to
terminal 23 (PG COMMON) of the PIOU, and
to zone 1 - zone 4 speakers.
6.15 Zone Page with BGM (multiple amplifiers).
This configuration also provides multiple-zone
paging capability, as in Paragraph 6.13. However,
separate amplifiers are used for each zone. Install
this option in accordance with the following steps
(refer to Figure 8-l 6):
1)
2)
3)
4)
5)
Connect the inputs from the paging amplifiers
to pins 13 (SPR) and 38 (SPT) of the PIOU.
Connect the music source to the music ampli-
fier input.
Connect the paging amplifier outputs to PIOU
relays
Kl
- K4 and zone 1 - zone 4 speakers.
Connect the music amplifier output to terminal
23 (PG COMMON) of the PIOU, and to the “C”
terminal of zone 1 - zone 4 speakers.
Connect zone 1 - zone 4 speakers “A” termi-
nal to the “B” contact of the PIOU relays Kl-
K4 respectively.
6.16 Night Ringing over External Page Zones
(PIOU only).
To allow the night ringing signal to be
sent over zone paging, install the paging amplifier
in accordance with the following steps (refer to
Figure 8-17). (Steps 1 - 6 are performed at the
MDF ’
1)
2)
3)
4)
5)
Cross-connect the amplifier input to pins 13
(SPR) and 38 (SPT) of the PIOU PCB.
Cross-connect the amplifier output A to the
PGINl - PGIN4 connector from the PIOU.
Cross-connect the amplifier output B to the
zone 1 - zone 4 speaker common line.
Cross-connect the PIOU PGOUTI - PGOUT4
to zone 1 - zone 4 speakers.
Cross-connect the amplifier output A to pin 9
(NHR) of the PIOU.
INSTALLATION-PERIPHERALS
SECTION 200-096-208
FEBRUARY 1991
6) Cross-connect a jumper from pin 34 (NHT) to
pin 23 (PG COMMON) from the PIOU PCB.
.
7)
In
Program 77-1,
set
LED 05 to OFF
and 06
to
ON.
Set
LED
08 to ON if door phones are
to ring over external page when the system is
in NIGHT mode.
8)
In
Program
78, enable the CO lines that are to
ring via external page when the system is set
in the NIGHT mode.
9)
In
Program
39, assign themormbuttons
to electronic telephones per the System Rec-
ord Sheets (see Note 2).
10) Press them or m button on an electronic
telephone to set the system into the NIGHT
mode. Test by calling into the system on a CO
line assigned
(Program
78) to night ring over
external page.
l
When ringing sounds (see Note 2) over
the page, press m 1 Ef 1 to answer.
NOTES:
1. All zones will ring with this option; night
ringing to selected zones is not possible.
2. The m or m buttons put CO lines in
NIGHT ring mode per
Program 15;
NT1 -
TENANT l/NT2-TENANT 2 CO line as-
signment.
7 STATION MESSAGE DETAIL
RECORDING (SMDR) PRINTER/CALL
ACCOUNTING DEVICE OPTIONS
7.00 An SMDR printer or call accounting device
may be connected to the system to provide a hard-
copy record of station activity (incoming, outgoing,
and transferred calls account code entries) on CO
lines or a printout of the customer data base. Call
record data is printed out at the completion of each
call, provided the call was at least 10 seconds in
length. Program SMDR with
Program
60, and use
Program
97 to have the SMDR printer display the
customer data base.
7.01 SMDR will send out special names for the
following types of calls: .
l
MSS:
Prints on DISA or DISC calls to stations
(see Note).
8-11