Filter
Top Products
42
Floor Standing Type
Adjustment of air Flow direction upwards/downwards
[In Cooling operation]
In cooling operation, move the louver with your hands so that the horizontal
air outlet points in a direction so that the cold air diffuses the entire room.
[In Heating operation]
In heating operation, move the louver with your hands so that the horizon-
tal air outlet points in a downward direction, towards the floor.
Adjustment of air Flow direction rightwards/leftwards
[In case of using unsymmetrical air directions]
Lift up the vertical louver lightly and direct it towards the desired
direction once completed lower the louver back down.
In this case, do not use the Swing function.
INFORMATION
• If cooling operation is performed with downward air outlet, dew may form on the surface of the cabinet
or the horizontal louver, resulting in possible dripping of water.
• If heating operation is performed with the horizontal air outlet actively moving, unevenness of the tem-
perature may increase within the room.
• Do not move the louver directly with your hands during swing operation; otherwise a fault may be caused.
The vertical louver does not stop immediately even if the
SWING/FIX
button is pushed.
To adjust the stop position, push the
SWING/FIX
button.
ON / OFF
FAN
TEMP.
SWING/FIXTIME
MODE
VENT
UNITSET CL
FILTER
RESET
TEST
TIMER SET
1, 2 3
[In case of automatic swing]
1
Push the
SWING/FIX
button during operation.
• [SWING ] is displayed and the air direc-
tion will automatically change rightwards/
leftwards.
In cases where one remote controller
controls multiple indoor units, it is possible to
set each indoor unit individually, so that the
air flow direction can be altered.
2
Push the
SWING/FIX
button again whilst the
vertical louver is moving will allow you
to stop the louver in the desired posi-
tion.
3
Swing button
UNIT
• To set up the air flow the direction individu-
ally, push the
UNIT
button to display each
indoor unit No. in a group control.
Then set up the air flow direction to the
desired indoor unit.
• If there is no display, all the indoor units can
be operated collectively.
• Every push of the
UNIT
button, will change
the display as shown in the figure.
1
2
In this case, do not use the
swing function.
Unit No. 1-1No display Unit No. 1-2
Unit No. 1-4 Unit No. 1-3
3-10. Timer Operation
The type of timer operation can be selected from the following three types.
OFF timer : The operation stops when the time on the timer has reached the set time.
Repeat OFF timer : The unit will stop, every time the set time period has elapsed.
ON timer : The unit will start when the time on the timer has reached the set time.
Timer operation
1
Push the TIMER SET button.
• The timer display (type) changes for every
push of the button.
• SET TIME and timer time displays flash.
2
Push the
TIME
buttons to select the “SET TIME”.
For every push of the button, the set time increases in the unit of 0.5 hr (30 minutes).
The maximum set time is 72.0 hr.
For every push of the
button, the set time decreases in the unit of 0.5 hr (30 minutes).
The minimum set time is 0.5 hr.
3
Push the SET button.
• The
SETTING
display disappears and the timer time display goes on.
(When the ON timer
is activated, the chosen time period will be displayed.
Once the time has been reached, all displays except the ON light will disappear.)
Cancel of timer operation
4
Push the CL button.
• TIMER display will disappear.
NOTICE
• When the unit stops after the timer has reached the preset time, the Repeat OFF timer will resume the
operation. However by pushing the
ON / OFF
button the repeat function will stop once the time on the
timer has again reached its set time.
4
3
2
1
ON / OFF
FAN
TEMP.
SWING/FIXTIME
MODE
VENT
UNITSET CL
FILTER
RESET
TEST
TIMER SET
OFF
(OFF timer) (Repeat OFF timer)
No display
(ON timer)
OFF ON