Filter
Top Products
Programming
Be sure the handset is in the cradle and the
SP-PHONE or MONITOR button is OFF.
1.
Set the MEMORY switch to “PROGRAM”.
“PITS-PGM NO ? +” will be displayed.
2. Press a programmable feature button.
The LCD will show “MOl/ P : Not Stored”
when nothing is stored in the
programmable feature button “1”.
When automatic line access number 9 and
the phone number 123-456-7890 has
been stored, “MOl/P : g-123-456-” will
be displayed.
3. Enter the line access number.
9 : automatic line access number
81: access number of trunk group 1
82: access number of trunk group 2
83: access number of trunk group 3
84: access number of trunk group 4
85: access number of trunk group 5
86: access number of trunk group 6
87: access number of trunk group 7
88: access number of trunk group 8
4. Enter the phone number.
You may enter punctuations in a phone
number.
The SAVE button is used as the “-‘I
button.
To erase a wrong entry, press the CLEAR
button.
The TRANSFER button is used as the
CLEAR button.
When you don’t want to display the dialed
phone number on the LCD in OneTouch
Dialing, press the ICM button before and after
dialing the phone number that you want to
keep secret. Do not press the ICM button before
line access number (9 or 81 through 88).
Example:
press the ICM button
The display shows the following when programming.
IMOllP: 9-123[456] 1
The display shows the following when dialing.
1
5. Press the MEMORY button.
The MEMORY indicator will be lit.
6. Repeat steps 2 to 5, to program on other
programmable feature button.
7. After programming all the numbers, return
the MEMORY switch to the “SET” position.
The MEMORY indicator will go out.
Dialing
1.
Lift the handset or press the SP-PHONE
button.
2. Press a programmable feature button.
0 You may press the CO button to select the
CO line directly after lifting the handset or
press the SP-PHONE button.
Conditions
Use the “+(FWD/DND)“, or “t(CONF)”
button for scrolling the display from side to
,
side.
The dialed phone number will be displayed
on the LCD of the KX-Tl23230 / KX-T123235 /
KX-T61631 / KX-T61630 /KX-T30830. The
dialed phone number can be kept secret by not
being displayed also.
The combinations of speed dialing, one-
touch dialing and manual dialing is possible.
The line access number (9) or trunk group
access number (81 through 88) should be
stored I
Continuous use of one touch dialing is
possible.
Example
:
[PROGRAMMABLE FEATURE l]
[PROGRAMMABLE FEATURE 21
In this case, programmable feature button
“2” should not include the line access
number or trunk group access number.
When dialing, the pause is automatically
entered after line access number (9) or trunk
group access number (81 through 88) are stored.
Features that can be accessed by using the
dialing button also can be programmed into
memory.
Refer to “One Touch Access for System
Features” page 4-52.
Examples:
Automatic line access number 9 and phone
number 123-4567 into the programmable
feature button ‘? “.
Programming:
Set the MEMORY switch to “PROGRAM”
position.
Press [PROGRAMMABLE FEATURE l]
Dial [9] [123-45671
Press [MEMORY]
Return the MEMORY switch to “SET”
position.
.
Dialing
Lift the handset.
Press [PROGRAMMABLE FEATURE l]
l
You may press the CO button to select the
r-n linn rlirn,-tl\r &tar
liftinn thn h.nnrlcnt
“V 1111-z “llb”,l)r call.zl IllUlwj LII-Z IlcLlI”*“L.
4-5