Filter
Top Products
System Operation
IMI 66-083
STATION SPEED DIAL PROGRAMMING
Station speed dial numbers can be stored by the
station user for later redial. The storage locations are
keypad digits 0 through 9 on the station. Before
attempting to program, decide on the following
items:
(1) the number or feature to be stored, (2) which
storage location will be used (0
-
9),
(3) the circuit that
the call will go over (individual line or intercom).
To
program numbers,
l Press
ITCM
+K
+K
2.
l
Dial a memory location (0 through 9). Listen for fast
tone bursts.
l
.Press specific line button,
ITCM
button, or dial 1
-
4
for line groups, to store circuit pre-selection.
-OR-
*
If no circuit pre-selection is desired, dial 0 (system
will choose last line used at calling station or prime
line if one is assigned to calling station).
l
Dial the number sequence to be stored. (Up to
sixteen digits can be stored. Valid digits include 0
-
9, #, and
+K.)
l
To store a pause if required, press
HOLD.
l
To store a hookflash if required, press
TAP.
Example:
Store a telephone number under location
0. The number is 1(804)555-2222. Program as follows:
ITCM,
+,
*,
2,0,
Line Button,
1,&O,
4,5,&S,
2,2,2,2.
To store another number,
l Press
TRANSICONF.
l
Press next speed dial location.
l
Make line pre-selection if desired.
l
Dial number for storage.
l
Repeat this procedure until all desired numbers are
stored.
To end station speed dial programming,
o
Press
MNTR (SPKR).
DIRECT STATION SELECTION/BUSY LAMP
FIELD
(DSWBLF)
PROGRAMMING
One-button intercom calling with visual indication of
telephone status can be programmed as
programmable buttons not assigned to lines.
To program DSS,
l Press
ITCM
+#
++
3.
l
Press programmable button
to be programmed as
DSS button.
l
Dial extension number.
.
Repeat last two steps for all desired
extension
numbers.
To end DSS programming,
l
Press
MNTR (SPKR).
NOTE: An autodial number can also be programmed
as a secondary function at every
DSSBLF
memory location. See Automatic Dialing
instructions for programming details.
PROGRAMMING AUTOMATIC
REDIAL
BUTTON
The system will allow the last previously dialed
number to be automatically and repeatedly redialed for
approximately ten minutes. A programmable button is
defaulted to provide this feature. A different
programmable button can be assigned for this function
if desired
To program another programmable button for use
as an automatic
redlal
button,
Press
ITCM
G%
% 1.
To remove function assignment,
Press current assigned programmable button, then
press
TRANS/CONF
button.
Press desired programmable button to receive
function. Listen for fast tone burst.
Press #to assign function.
Press
MNTR (SPKR) to end.
PROGRAMMING RESPONSE MESSAGE
BUTTON
The system will allow a station user to make a
non-verbal response to
an
intercom call or to a secure
off -hook voice announcement. This response will
provide
a
preprogrammed message for display at the
*
calling station if it is an LCD speakerphone.
To assign programmable button for non-verbal
one-button response,
l
‘PresslTCM+++l.
l
Press desired programmable button.
0
Dial 5.
0
Dial message location number
(1-O).
NOTE: The response message is preprogrammed and
made available for use by attendant
programming.
l
Press MNTR
(SPKR) to
end.
0
Label button.