Filter
Top Products
l
Selection
2: Line group assignment (assigns line to
line groups, will be reserved
if
the hybrii strap is not
installed)
l
Selection
3: Line dialing mode (pulse or tone to
match the connected line)
l
Selection
4: Line privacy release (releases privacy
on a line)
0
Selectlon
5: Line toll restriction table assignment
l
Selection
6: Line abandoned hold release time
l
Selection
7: Set up a line (Using a model line)
(provides a means of programming a group of lines
to match the programming of a model line)
l
Selection
8: Assign name to line.
l
Selection
9: Assign line to department.
l
Selectlon 10:
Exclusive hold.
l
Selection 11:
Voice mail line ID (Specifies
identification number of a particular line to the voice
mail accessory for personalized call coverage)
l
Selection
12: DISD assignment (Assigns DISD to
lines and specifies calling characteristics of them)
Station C.O.S. Programming
1. Set Up a Station (Using a Model Station)
2. Assign Name to Station
3. Assign Station to Department
4. Assign Station
to
SOHVA Group
5. Line/ Intercom Features
6. Ringing Assignment
7. Button Mapping
8. Toll Restriction Administration
9. Automatic Busy/ RNA Call Forwarding
10. Miscellaneous Feature Programming
11. Return To Previous Menu
Enter Selection:
STATION COS MENU SELECTION
IMI 66-083
System Programming ,
l
Selectlon
2: Assign name to station
l
Selection
3: Assign station to department
l
Selectlon 4:
Assign station to SOHVA groups
0
Selectlon
5: Line/Intercom features
l
Prime Line (assign prime line, prime group,
prime intercom, or clear all)
.
Ringing Line Preference (enable or disable)
l
Line Access Deny (enable or disable station
access to a line)
l
Line Originate Deny (enable or disable station
ability to originate a call on a line)
l
Idle Line Preference (enable or disable access
to an idle line when station is taken off hook)
l
Block Voice Announce Intercom Call
l
Audible Monitoring (audible ringing sounded for
stations with BLF appearance at programmed
station)
In each station COS menu selection, after choosing
the feature, enter a station port number which is to be
assigned to it and enter line port ‘numbers where
. . .
prompted. Muttiple station number entries are allowed
for some features as prompted.
l
Selectlon 1:
Set up a station (Using a model
station) (program a group of stations to match the
programming of a model station)
l
Selection 6:
Ringing assignment
l
Personal Ringing Tones (One of four different
tones can be chosen. Refer to page 4-29 for
frequencies if required.)
l
Direct/Delayed Ringing (of each line assigned to
programmed station)
l
Night Ringing (enable or disable night transfer,
of ringing, to programmed station for
programmed lines)
l
SelectIon
7: Button mapping (assign functions to
buttons)
Special
Note: Affhough buttons are identified by
Ax and Bx codes as shown in
Figure
4-l
on page
449 and on fhe programming overlay supplied
with the system, do not type an
*A”or
“B” before
the buffon number when identifying it for function
assignment. To do so, causes the system to
interpret the typed entry as a line number choice
instead of a button number choice.
l
Functions that can be assigned are identified per
the following list:
To display list, enter
?.
Return to key mapping with
Control
2.
BLK . . . . . . . . . Blank
Line (1
-
24)
~?::::IStatiin
(10
-
57)
DND
. . . . . . . .
Do Not Disturb
PRI
. . . . . . . . . . Privacy
IC2
. . . . . . . . . . 2nd
Intercom
SAV . . . . . . . . . Save
ACC
. . . . . . . . Account Code
Button
ZPX
. . . . . . . . . Zone
Page
(l-3)
AC . . . . . . . ;... All
Call
ACB
. . . . . . . . Auto
Callback
CF
. . . . . . . . . . . Call
Forward
4-89