Filter
Top Products
l
Selection 4: Load/Save COS data (on cassette
tape and the transfer of this data through remote
programming)
l
Selection 5 : Serial communication parameters (for
data port A and data port B)
l
Selection
6: COS data printout
l
Selection
7: Set clock date/time.
l
Selection
8: SMDA programming (Configures the
Station Message Detailed Accounting feature. Also
refer to page 4-59 for an explaination of call costing
and SMDA reporting.)
l
Assign Area Codes
/
Prefixes to Bands
l
Enter band number O-7, enter 0 for no band, or
enter area codes or prefixes as 200-999.
l
Set Dial Time Limit (non-costed time allowed for
dialing to take place in l/l 0 min)
l
Set Answer Time Limlt (non-costed time allowed
for call to ring and be answered in l/l 0 min)
l
Define Department Numbers (Calls can be
costed on a department basis by department
basis.)
.
Assign Stations to Departments (for costing by
department)
l
Set Account Codes (Calls can be identified by
account code for costing by catagory.)
l Clear Account Codes
l
Enable Account Codes Wiih Verify (User
account code entry is compared
with
programmed account code.)
l
Enable Account Codes Without Verify (User
account code entry is not compared with
programmed account code.)
l Disable Account Codes
9
Account Code Message Display Parameters
(LCD speakerphones can prompt users for
account code entry on incoming and/or outgoing
calls.)
l
Account Code Message Display Time
l
Maximum Account Code Length
9
Call Cost Tables
l
Call Cost Exception Tables
.
Automatic Reports (Call cost reports can be
produced for prfnting.)
l
SMDA Delete By Attendant (allows attendant to
delete SMDA records)
l
SelectIon
9: SMDR print parameters (enables Or
disables call cost reporting along with a Station
Message Detail Report).
IMI 66-083
System Progamming
l
Selectlon 10:
LogicaVphysical assignments
-
stations (For example; assign station extension 25
to station port 25. Also refer to the discussioin
provided on page 3-6.)
l
Selection 11:
Logical/physical assignments
-
lines
(For example; assign line 1 to line port 1. Also refer
to the discussion on page 3-5.)
l
Selectlon 12:
Automatic station relocation (allows
individual features to be physically relocated without
losing their programming parameters and extension
asignments)
l
Selection 13:
Feature inhibit programming (allows
individual features to be inhibited)
l
Selection 14:
Enable all inhibited features (will
enable all features inhibited
with
selection 13)
l
Selection 15:
LCD messages (programs the
messages for the LCD messaging and response
messaging features)
l
Selectlon 16:
Software version number (identifies
the software release version of the system)
Line C.O.S. Programmlng
1. Line Type
2. Line Group Assignment (reads “Reserved” if no
hybrid strap is installed)
strap installed)
3. Line Dialing Mode
4. Line Privacy Release
5. Line Toll Restriction Table Assignments
6. Line Abandoned Hold Release Time
7. Set Up a Line ( Using a Model Line )
8. Assign Name to Line
9. Assign Line to Department
10. Exclusive Hold
11 .Voice Mail Line I.D.
12. D.I.S.D. Assignments
13. Return To Previous Menu
Enter Selection:
LINE COS MENU SELECTIONS
In each line COS menu selection, after choosing the
feature, enter all line port numbers which are to be
assigned to it.
l
Selection 1:
Llne type (specifies the characteristics
of the line port)
9
Disabled
l
Auxiliary (Configures port for installation of
external paging amplifier.)
.
COlPABX (Typical line connection)
4-88