Cisco Systems 10200 Telephone User Manual


 
A-6
Cisco BTS 10200 Softswitch Operations and Maintenance Guide, Release 6.0.x
OL-16000-07
Appendix A Feature Tones
Tone Frequencies and Cadences
Tone Frequencies and Cadences
Tones are requested by the BTS and delivered to the subscriber or operator by the MGW. Some MGWs
can be provisioned to play tone cadences different than the ones described in this table.
SC1D-ACT
SC2D-ACT
STUTTER TONE Stutter tone is used once after the subscriber enters the *74 (SC1D
activation) or *75 (SC2D activation) to begin the process of collecting
the information required to provision one of the speed call slots. After a
speed call slot has been successfully provisioned, the subscriber will
again receive the stutter tone to signify that the speed call slot was
successfully provisioned.
VMWI
3
STUTTER TONE The subscriber has VMWI and has a message waiting, but the serving
MGW does not have a visual indicator.
1. When more than one condition is listed for a single tone, any one of the conditions can cause the tone to be played.
2. For more information on the screening list, refer to the Cisco BTS 10200 Softswitch System Description.
3. MWI = message waiting indicator; VMWI = visual message waiting indicator.
Table A-1 Feature Tones (continued)
Feature Tone Condition(s) That Initiate Tone
1
Table A-2 Subscriber and Operator Tone Descriptions
Tone Frequency (Hz) Cadence Played by MGW
Alerting pattern (ringing) 1 440 + 480 2 sec on, 4 sec off, repeating
Alerting pattern (ringing) 2 440 + 480 0.8 sec on, 0.4 sec off, 0.8 sec on, 4.0 sec off, repeating
Alerting pattern (ringing) 3 440 + 480 0.4 sec on, 0.2 sec off, 0.4 sec on, 0.2 sec off, 0.8 sec on, 4 seconds
off, repeating
Alerting pattern (ringing) 4 440 + 480 0.3 sec on, 0.2 sec off, 1 sec on, 0.2 sec off, 0.3 sec on, 4 sec
off, repeating
Alerting pattern (ringing) 5 440 + 480 0.5 sec on once
Alerting pattern (ringing) 6 440 + 480 1 sec on, 3sec off, repeating
Busy verification
(used for operator BLV
1
)
440 2 sec burst, followed by 0.5 sec burst every 10 sec
CW tone 440 0.3 sec on once
CW Type 1 440 0.3 sec on once
CW Type 2 440 0.1 sec on, 0.1 sec off, 2 times
CW Type 3 440 0.1 sec on, 0.1 sec off, 3 times
CW Type 4 440 0.1 sec on, 0.1 sec off, 0.3 sec on, 0.1 sec off, 0.1 sec on
Confirmation tone 350 + 440 0.1 sec on, 0.1 sec off, 3 times
Dial tone 350 + 440 steady on
Line busy tone 480 + 620 0.5 sec on, 0.5 sec off, repeating
Message waiting indicator tone 350 + 440 10 bursts (0.1 sec on, 0.1 sec off), then steady on
Off-hook warning tone
(receiver off-hook tone)
1400 + 2060 +
2450 + 2600
0.1 sec on, 0.1 sec off, repeating