Filter
Top Products
2. Programming Concepts
2-41
Special
D
Content
ES2
EX2
SS
2
SA
2
SX
2
OFF
Ø
ON
STOP
Ø
RUN
RUN
Ø
STOP
Attrib.
Latch
-ed
Default
D1070
↓
D1085
Feedback data (ASCII) of Modbus
communication. When PLC’s RS-485
communication instruction receives feedback
signals, the data will be saved in the registers
D1070~D1085. Usres can check the received
data in these registers.
○ ○ ○ ○
0 - - R NO 0
D1086
High word of the password in DVP-PCC01
(displayed in hex according to its ASCII codes)
○ ○ ○ ○
0 - - R/W NO 0
D1087
Low word of the password in DVP-PCC01
(displayed in hex according to its ASCII codes)
○ ○ ○ ○
0 - - R/W NO 0
D1089
↓
D1099
Sent data of Modbus communication.
When PLC’s RS-485 communication instruction
sends out data, the data will be stored in
D1089~D1099. Users can check the sent data in
these registers.
○ ○ ○ ○
0 - - R NO 0
D1109*
COM3 (RS-485) Communication protocol
○ ╳ ○ ○
H’86 - - R/W NO H’86
D1110*
Average value of EX2/SX2 analog input channel 0
(AD 0) When average times in D1062 is set to 1,
D1110 indicates present value.
○ ╳ ╳ ○
0 - - R NO 0
D1111*
Average value of EX2/SX2 analog input channel 1
(AD 1) When average times in D1062 is set to 1,
D1111 indicates present value
○ ╳ ╳ ○
0 - - R NO 0
D1112*
Average value of EX2/SX2 analog input channel 2
(AD 2) Whenaverage times in D1062 is set to 1,
D1112 indicates present value
○ ╳ ╳ ○
0 - - R NO 0
Average value of 20EX2/SX2 analog input
channel 3 (AD 3) Whenaverage times in D1062 is
set to 1, D1113 indicates present value
○ ╳ ╳ ○
0 - - R NO 0
D1113*
Displaying the status of the analog input channel
of 30EX2
○ ╳ ╳ ╳
0 - - R NO 0
D1114*
Enable/disable 20EX2/SX2 AD channels
(0: enable (default) / 1: disable)
bit0~bit3 sets AD0~AD3.
P.S. 30EX2 does not support this function.
○ ╳ ╳ ○
0 - - R/W YES 0
20EX2/SX2 analog input/output mode setting
○ ╳ ╳ ○
0 0 0 R/W YES 0
D1115*
30EX2 analog input/output mode setting
○ ╳ ╳ ╳
- - - R/W YES H’FFFF
D1116*
Output value of analog output channel 0 (DA 0) of
EX2/SX2
○ ╳ ╳ ○
0 0 0 R/W NO 0
D1117*
Output value of analog output channel 1 (DA 0) of
20EX2/SX2
P.S. 30EX2 does not support this function.
○ ╳ ╳ ○
0 0 0 R/W NO 0
D1118*
EX2/SX2 sampling time of analog/digital
converstion. Default: 2. Unit: 1ms. Sampling time
will be regarded as 2ms if D1118≦2
○ ╳ ╳ ○
2 - - R/W YES 2
D1120*
COM2 (RS-485) communication protocol
○ ○ ○ ○
H’86 - - R/W NO H’86
D1121*
COM1(RS-232) and COM2(RS-485) PLC
communication address
○ ○ ○ ○
- - - R/W Yes 1
D1122
COM2(RS-485) Residual number of words of
transmitting data
○ ○ ○ ○
0 0 - R NO 0
D1123
COM2(RS-485) Residual number of words of the
receiving data
○ ○ ○ ○
0 0 - R NO 0