Filter
Top Products
Overview of Menus
30
6.0 OVERVIEW OF MENUS
There are two ways to access the Universal Monitor: the LCD on the front of the enclosure and the
Service Terminal Interface, which is accessible through any computer using a communications pro-
gram. Many viewing and configuration tasks can be performed through either interface, but some are
available only through the Service Terminal Interface.
• Step-by-step instructions for all functions appear in Sections 7.0 through 9.0. These instructions
use examples of LCD screens to illustrate most functions, except those not available via the LCD.
• Examples of all Service Terminal Interface screens appear in Appendix A - Service Terminal
Interface, along with instructions on how to connect to the Service Terminal Interface.
Table 12 lists all Universal Monitor functions and shows whether they can be performed through the
LCD interface and where to find information.
Table 12 Guide to Universal Monitor functions
Function
Can be performed via: Where to find:
LCD
Service
Terminal
Instructions on
using function
Service Terminal
screen examples
VIEW STATUS FUNCTIONS
View Active Alarms ✔✔ page 33 page 93
View Alarm Log ✔✔ page 34 page 94
View Event Log ✔✔ page 35 page 95
View Trend Log ✔✔ page 36 page 96
View Input Status ✔✔ page 37 page 97
View Output Status ✔✔ page 38 page 98
View Pager Numbers ✔✔ page 39 page 99
SILENCE ALARM & BACK UP LOGS FUNCTIONS
Silence Alarm (On the LCD, press any key to silence an alarm) ✔✔ page 40 page 100
Back Up Log Files — ✔ page 41 page 101
SYSTEM & CONTROL FUNCTIONS
Login ✔✔ page 43 page 104
Setup System ✔✔ page 45 page 105
Setup Input ✔✔ page 45 page 106
Setup Common Alarm ✔✔ page 48 page 108
Setup Sensor ✔✔ page 49 page 109
Setup I/O Matrix ✔✔ page 55 page 111
Setup Output ✔✔ page 58 page 117
Pager Setup - Pager Number & PIN ✔✔ page 64 page 119
Pager Setup - Communications Check — ✔ page 66 page 119
Modem Setup - Initialization String ✔✔ page 60 page 120
Modem Setup - Enter Universal Monitor Phone Number — ✔ page 62 page 120
Modem Setup - Enable Modem Diagnostic Messages — ✔ page 62 page 120
Modem Setup - Change Modem Dial Prefix — ✔ page 62 page 120
Modem Setup - Change Modem Hang Up Delay After a Call — ✔ page 62 page 120
Setup System Info ✔✔ page 68 page 121
Change Password ✔✔ page 69 page 121
Change Date & Time/Automatic Daylight Saving Time ✔✔ page 69 page 122
Setup Site ID ✔✔ page 70 page 122
Connect Battery ✔✔ page 70 page 123
Backup and Upload Configuration File — ✔ page 71 page 123
Setup Serv Ph Num - Enter Phone Number ✔✔ page 74 page 124
Setup Serv Ph Num - Communications Check — ✔ page 75 page 124
Factory Defaults ✔✔ page 76 page 125
Perform Firmware Update — ✔ page 76 page 125
Initiate Remote Alarm Test — ✔ page 78 page 126
Setup Exp Board - Optional Expansion Board ✔✔ page 79 page 127
Manual Output Ctrl ✔✔ page 80 page 128
Clear Alarms & Logs ✔✔ page 81 page 130
Clear Active Alarms ✔✔ page 81 page 130
Clear the Alarm Log ✔✔ page 81 page 130
Clear the Event Log ✔✔ page 82 page 131
Clear the Trend Logs ✔✔ page 82 page 131