Filter
Top Products
Continued from front matter. . .
8.CD.NL.A.03.11.97.R1.J.CW2B
Warranty (contd)
Agilent does not warrant
that the operation of Agilent
products will be
uninterrupted or error free.
If Agilent is unable, within a
reasonable time, to repair or
replace any product to a
condition as warranted,
customer will be entitled to a
refund of the purchase price
upon prompt return of the
product.
Agilent products may
contain remanufactured
parts equivalent to new in
performance or may have
been subjected to incidental
use.
The warranty period begins
on the date of delivery or on
the date of installation if
installed by Agilent. If
customer schedules or delays
Agilent installation more
than 30 days after delivery,
warranty begins on the 31st
day from delivery.
Warranty does not apply to
defects resulting from
(a) improper or inadequate
maintenance or calibration,
(b) software, interfacing,
parts or supplies not
supplied by Agilent,
(c) unauthorized
modification or misuse,
(d) operation outside of the
published environmental
specifications for the
product, or (e) improper site
preparation or maintenance.
TO THE EXTENT
ALLOWED BY LOCAL
LAW, THE ABOVE
WARRANTIES ARE
EXCLUSIVE AND NO
OTHER WARRANTY OR
CONDITION, WHETHER
WRITTEN OR ORAL, IS
EXPRESSED OR IMPLIED
AND AGILENT
SPECIFICALLY
DISCLAIMS ANY IMPLIED
WARRANTIES OR
CONDITIONS OF
MERCHANTABILITY,
SATISFACTORY QUALITY,
AND FITNESS FOR A
PARTICULAR PURPOSE.
Agilent will be liable for
damage to tangible property
per incident up to the greater
of $300,000 or the actual
amount paid for the product
that is the subject of the
claim, and for damages for
bodily injury or death, to the
extent that all such damages
are determined by a court of
competent jurisdiction to
have been directly caused by
a defective Agilent product.
TO THE EXTENT
ALLOWED BY LOCAL
LAW, THE REMEDIES IN
THIS WARRANTY
STATEMENT ARE
CUSTOMER’S SOLE AND
EXCLUSIVE REMEDIES.
EXCEPT AS INDICATED
ABOVE, IN NO EVENT
WILL AGILENT OR ITS
SUPPLIERS BE LIABLE
FOR LOSS OF DATA OR
FOR DIRECT, SPECIAL,
INCIDENTAL,
CONSEQUENTIAL
(INCLUDING LOST
PROFIT OR DATA), OR
OTHER DAMAGE,
WHETHER BASED IN
CONTRACT, TORT, OR
OTHERWISE.
For consumer transactions
in Australia and New
Zealand: the warranty terms
contained in this statement,
except to the extent lawfully
permitted, do not exclude,
restrict or modify and are in
addition to the mandatory
statutory rights applicable to
the sale of this product to
you.
Assistance
Product maintenance
agreements and other
customer assistance
agreements are available for
Agilent products.
For any assistance, contact
your nearest Agilent Sales
and Service Office.
Safety Considerations
(contd)
WARNING
ANY INTERRUPTION OF
THE PROTECTIVE
GROUNDING
CONDUCTOR (INSIDE OR
OUTSIDE THE
INSTRUMENT) OR
DISCONNECTING THE
PROTECTIVE EARTH
TERMINAL WILL CAUSE A
POTENTIAL SHOCK
HAZARD THAT COULD
RESULT IN PERSONAL
INJURY. (GROUNDING
ONE CONDUCTOR OF A
TWO CONDUCTOR OUT-
LET IS NOT SUFFICIENT
PROTECTION.)
Whenever it is likely that the
protection has been
impaired, the instrument
must be made inoperative
and be secured against any
unintended operation.
If this instrument is to be
energized via an
autotransformer (for voltage
reduction) make sure the
common terminal is
connected to the earthed pole
terminal (neutral) of the
power source.
Instructions for adjustments
while covers are removed
and for servicing are for use
by service-trained personnel
only. To avoid dangerous
electric shock, do not
perform such adjustments or
servicing unless qualified to
do so.
For continued protection
against fire, replace the line
fuse(s) only with 250V
fuse(s) of the same current
rating and type (for example,
normal blow, time delay).
Do not use repaired fuses or
short circuited fuseholders.
Acoustic Noise Emissions
LpA<47 dB at operator
position, at normal
operation, tested per
EN 27779. All data are the
results from type test.
Geräuschemission
LpA<47 dB am Arbeits
platz, normaler Betrieb,
geprüft nach EN 27779.
Die Angagen beruhen auf
Ergebnissen von
Typenprüfungen.
Electrostatic Discharge
Immunity Testing
When the product is tested
with 8kV AD, 4kV CD and
4kV ID according to
IEC801-2, a system error
may occur that may affect
measurement data made
during these disturbances.
After these occurrences, the
system self-recovers without
user intervention.