Filter
Top Products
Page 62 - Regulatory Instructions for Use Safety and Homologation Statements
Page 62 - Safety and Homologation Statements IP Office Installation Manual
Regulatory Instructions for Use 40DHB0002USCL – Issue 9 (28th October 2003)
IP Office Operation in EU
1. 999 and 112 calls must not be barred. Doing so will invalidate the approval.
2. All connections at the MDF shall be identifiable by suitable labeling.
3. The CE mark displayed on IP Office equipment indicates the systems compliance with
the EMC, LVD, and R&TTE Directives and common technical regulations for Primary
Rate and Basic Rate ISDN.
4. All ports for the connection of other non-telecommunications apparatus have a Safety
Extra Low Voltage (SELV) safety status.
IP Office Operation in New Zealand
The grant of a Telepermit for any item of terminal equipment indicates only that Telecom
has accepted that the item complies with minimum conditions for connection to its
network. It indicates no endorsement of the product by Telecom, nor does it provide any
sort of warranty. Above all, it provides no assurance that any item will work correctly in all
respects with another item of Telepermitted equipment of a different make or model, nor
does it imply that any product is compatible with all of Telecom's network services.
IP Office Operation in USA
FCC Notification
This equipment is registered with the ACTA (Administrative Council for Terminal
Attachments) in accordance with FCC Part 68 of its rules. In compliance with those rules,
you are advised of the following:
• Means of Connection. Connection of this equipment to the telephone network shall be
through a standard network interface jack. Connection to 1.544-MBps digital facilities
must be through a USOC RJ48C. Connection to the Analog Trunk facilities must be
through a USOC RJ45S.
• Notification to the Telephone Companies. Before connecting this equipment, you or
your equipment supplier must notify your local telephone company’s business office of
the telephone number or numbers you will be using with this equipment.
• The facility interface codes (FIC) for 1.544-MBps digital connection (i.e. IP400 Office
PRI-T1) are 04DU9.BN, 04DU9.DN, 04DU9.IKN, 04DU9.ISN.
• The facility interface code (FIC) for analog trunk connection (i.e IP400 Office Quad
Analog Trunk-LS) are OL13A, OL13B, OL13C, 02AC2, 02LA2, 02LB2, 02LC2, 02LR2,
02LS2.
• The facility interface code (FIC) for analog trunk connection (i.e. IP400 Office
ATM16-LS/GS) are OL13A, OL13B, OL13C, 02AC2, 02GS2, 02LA2, 02LB2, 02LC2,
02LR2, 02LF2.
• The Service Order Code (SOC) for 1.544-MBps digital connection (i.e. IP400 Office
PRI-T1) is 6.0Y.
• The Service Order Code (SOC) for analog trunk connection (i.e. IP400 Office Quad
Analog Trunk-LS) is 9.0Y.
• Disconnection. You must also notify your local telephone company if and when this
equipment is permanently disconnected from the line or lines.
• Hearing Aid Compatibility. The custom telephone sets for this system are compatible
with inductively coupled hearing aids as prescribed by the FCC.
Ringer Equivalence Number (REN). The REN is used to determine the number of devices
that may be connected to the telephone line. Excessive RENs on the line may result in the
devices not ringing in response to an incoming call. In most, but not all, areas, the sum of
the RENs should not exceed five. To be certain of the number of devices that may be
connected to the line, as determined by the total RENs, contact the local telephone
company to determine the maximum REN for the calling area.