Filter
Top Products
IP403 Office Platform IP403 Office - Front View - Page 11
IP Office Installation Manual IP403 Office Platform - Page 11
40DHB0002USCL – Issue 9 (28th October 2003) IP403 Office - Front View
IP403 Office - Front View
Y
ellow LEDs
LEDs 1-3 = Expansion Ports 1-3 status
LEDs 4-7 = ISDN 1-4 status
LED 8 = WAN status
Green LEDs
Terminal connected
DT
or
DS Ports 1-8
Unit Status LED
Red = Alive but not initiated
Green = Running OK
Analog Telephone Ports 1& 2
(
POTs
)
LAN Ports 1-8
Port 8
(
Cascade
p
ort
)
Y
ellow LED
LAN Collision
Green LED
Solid Green LED - LAN OK
Flashing Green - LAN OK and active
Y
ellow LED
On - 100Mbps operation
0ff - 10Mbps operation
Cascade Switch
For port eigh
t
Port connections
• DT/DS Ports
- DT ports are for connection to Avaya 2000 series telephones (see page 5).
- DS ports are for connection to Avaya 4400, 2420 and/or 6400 series telephones
(see page 5).
At default DT ports are set to A-Law PCM encoding and DS ports to either A-Law or µ-
Law PCM encoding (see page 28). However, both ports can be switched in software -
refer to the Administration Manager Manual for details).
Using DT Line Cords (see page 68) and standard structured wiring, these RJ45 ports
can be extended to the required telephone location. In addition, converters can be
used to provide BT New Plan sockets (431A/631A) if required (see page 77). When
telephones are equipped with line cords that terminate in RJ11 plugs, then pin-to-pin
RJ11/RJ45 adapters should be used.
• Plain Ordinary Telephone (POTS) Ports: These two ports are used for connection to
standard analog telephones, fax machines and modems. They must not be connect to
trunks. Using standard structured wiring, these RJ45 ports can be extended to the
required telephone location. Converters can be used to provide BT New Plan sockets
(431A/631A) if required (see page 77). When devices are equipped with line cords that
terminate in RJ11 plugs, then pin-to-pin RJ11/RJ45 adapters should be used.
• LAN Ports: The eight auto-negotiating 10/100 BaseT LAN hub ports are used for PC
and server connectivity. They can also be used to connect to the optional IP400 WAN3
Expansion Module (see page 26) and IP telephones. LAN ports allow information
relating to incoming and outgoing telephone calls to be forwarded to PC based
applications. They also provide access to the router functionality/configuration of the
IP403 Office platform for both data and Voice over IP (VoIP) calls. (Where IP telephony
is required, a suitable switch LAN switch with QoS capabilities.) This eight port auto-
negotiating 10/100 BaseT LAN hub has a single MAC address (printed on the base of
the unit).
Where more than eight LAN connections are required, the eighth LAN port can be used
for cascading to other hubs. The Cascade pushbutton to the right of this port is used to
set the mode. When the Cascade switch is in the out position the port can be
connected to another hub without the need for a crossover cable, i.e. the port is an MDI
type port. When the Cascade switch is in the in position the port can be connected
directly to a PC.
Cables
IP403 Office DT PRI 30 E1 & DS PRI 24 T1 are supplied with one red CAT5E cable.
IP403 Office DT BRI 8 & DS Analog 4 are supplied with four red CAT5E cables. For Port
Pinouts and Cables, refer to pages 63 and 67 respectively.