Filter
Top Products
13
Telephone Operation
connected, be sure the handset seats
properly.
• With a headset connected, you make or
answer calls as usual using the keys on
the handset.
• You can use an optional handset holder
(available from your local RadioShack
store) to hang the handset on your belt
for greater convenience.
MEMORY DIALING
You can store up to 10 phone numbers and
names in memory, then dial a stored number
by entering its memory location number.
Each number can be up to 20 digits, and
each name can be up to 14 characters.
Storing a Name and Number in
Memory
When you are storing a number in memory,
an error tone sounds and the phone exits the
storing process if you wait more than 20
seconds between each keypress. If you
receive a call during memory entry, the
phone exits the storing process.
To store a number and name in memory:
1. Lift the handset.
2. Hold down
MEM
until
C[cehoý Ijeh[
C[cehoý Ijeh[C[cehoý Ijeh[
C[cehoý Ijeh[
and a
list of memory location numbers appear.
3. Press the appropriate numbers (
0
–
9
) to
choose a memory location.
4. Press
SELECT
.
Ijeh[ýDWc[
Ijeh[ýDWc[Ijeh[ýDWc[
Ijeh[ýDWc[
appears. If
you do not want to enter a name, skip to
Step 6.
5. To enter a name, use the number keys.
Refer to the letters on the number keys
to select the desired letter. Press the key
once for the first letter in the upper case,
press twice for the second letter in the
upper case, and so on. To enter the
lower case letter, press four times (or
five times) to display the first letter in
lower case, five or six times for the
second letter, and so on.
For example, to enter
John
: press
5
once; upper case
@
@@
@
appears. Then press
6
six times; lower case
e
ee
e
appears. Press
4
five times; lower case
^
^^
^
appears.
Finally, press
6
five times; lower case
d
dd
d
appears.
To enter two letters from the same key in
a row, press #/
7
77
7
to move the cursor to
the next position. For example to enter
AB
, press
2
;
7
77
7
appears. Then press #/
7
77
7
,
the cursor moves to the next position,
then press
2
twice so
8
88
8
appears.
To enter a space, press #
/
7
77
7
twice
without entering any character.
To enter a number, repeatedly press the
corresponding number key until the
number appears.
To enter a special character, use
0
. Each
time you press
0
, the following
characters appear in this order:
-
--
-ýçý#ý
ýçý#ýýçý#ý
ýçý#ý)
))
)ýâ
ýâýâ
ýâýá
ýáýá
ýá
(space)
&
&&
&
If you make a mistake, use
TONE/
6
66
6
/* or
#/
7
to move the cursor over the error,
then enter the correct character, or
press
DELETE
to delete a character. To
delete all characters, briefly hold down
DELETE
.
6. Press
SELECT
.
Ijeh[ýDkcX[hý
Ijeh[ýDkcX[hýIjeh[ýDkcX[hý
Ijeh[ýDkcX[hý
appears.
7. Enter the phone number and any tone or
pause entries (see “Using Tone Services
on a Pulse Line” on Page 12 and
“Entering a Pause” on Page 14).
Note:
Each tone or pause entry uses
one digit of memory.