Filter
Top Products
10
Installation
>_]^
>_]^>_]^
>_]^
,
H_d][h
H_d][hH_d][h
H_d][hJof[ý7
Jof[ý7Jof[ý7
Jof[ý7ýBem
ýBemýBem
ýBem
,
H_d][hý
H_d][hýH_d][hý
H_d][hýJof[ý
Jof[ýJof[ý
Jof[ý8ý>_]^
8ý>_]^8ý>_]^
8ý>_]^
, or
ý
ýý
ý
H_d][hý
H_d][hýH_d][hý
H_d][hýJof[ý
Jof[ýJof[ý
Jof[ý8ýBemý
8ýBemý8ýBemý
8ýBemý
appears.
TURNING THE BASE’S
RINGER ON/OFF
You can set the base’s ringer to high or low,
or turn it off.
1. Press
MENU
four times. The phone
announces “Ringer volume” and its
current setting. The current setting also
displays.
2. Press
SET
to enter the setting mode.
The system exits the setting mode when
you:
• wait more than 20 seconds between
key presses
• receive an incoming call
• press
PLAY/STOP
•press
TALK
on the handset
Start again at Step 1.
3. Press
SKIP/
;
or
:
/REPEAT
to change
the setting. The system announces the
setting and displays
>_
>_>_
>_
,
Be
BeBe
Be
, or
E<
E<E<
E<
.
4. Press
SET
to store the setting.
5. Press
PLAY/STOP
to exit the menu
setting.
Even when you turn off the base’s ringer, you
can still make or receive calls using this
phone. Telephones on the same line (and
the handset if it is away from the base) still
ring when there is an incoming call.
SETTING AUTO TALK
Your phone is preset so you must press
TALK
to answer a call. With auto talk turned
on, you can answer a call by lifting the
handset from the base or, if the handset is
away from the base, by pressing any key.
To turn auto talk on or off:
1. Lift the handset and hold down
CALL ID
until the setup menu appears.
2. Press
SELECT
to change the auto talk
setting.
Ed
EdEd
Ed
or
E\\
E\\E\\
E\\
appears.
3. To clear the display when you finish,
press
CALL ID
or return the handset to
the base.
TURNING CALLER ID/CALL
WAITING ON/OFF
If you have Call Waiting and Caller ID
service, you can set the system to show
Caller ID information for an incoming call
even while you are on the phone.
To set the Caller ID/Call Waiting:
1. Lift the handset and hold down
CALL ID
until the menu appears.
2. Press
2
or
9
99
9
to select
9?:9Mý
9?:9Mý9?:9Mý
9?:9Mý
(Caller ID/
Call Waiting).
3. Press
SELECT
to change the Caller ID/
Call Waiting setting.
Ed
EdEd
Ed
or
E\\
E\\E\\
E\\
appears.
4. Return the handset to the base to store
the new setting.
STORING YOUR AREA
CODE
You can store your local area code in the
phone’s Caller ID record so it does not show
the area code if the received call is from your
local area. If for some reason you need to
dial the area code (or store in the memory),
you can add it afterwards. “Adding/Deleting
the Area Code” on Page 16.