Filter
Top Products
www.vtechphones.com
78
FCC Part 15
Warning: Changes or modications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
The equipment has been tested and found to comply with part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet or on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
To ensure safety of users, the FCC has established criteria for the amount of radio frequency energy that can be safely absorbed by a user or bystander according to the intended usage of the prod
-
uct. This product has been tested and found to comply with the criteria. The handset has such a low power that it does not require testing. It may be safely held against the ear of the user. The base
unit shall be installed & used such that parts of the user’s body other than the hands should be maintained at a comfortable distance of approximately 20cm or more.
FCC Part 68 and ACTA
If this equipment was approved for connection to the telephone network prior to July 23, 2001, it complies with Part 68 of the Federal Communications Commission (FCC) rules. If the equipment
was approved after that date, it complies with the Part 68 rules and with Technical Requirements for Connection of Equipment to the Telephone Network adopted by the Administrative Council for
Terminal Attachments (ACTA). We are required to provide you with the following information.
1. Product identier and REN information
The label on the back or bottom of this equipment contains, among other things, an identier indicating product approval and the Ringer Equivalence Number (REN). This information must be
provided to your local telephone company upon request. For equipment approved prior to July 23, 2001, the product identier is preceded by the phrase “FCC Reg No.” and the REN is listed
separately. For equipment approved after that date, the product identier is preceded by “US” and a colon (:), and the REN is encoded in the product identier without a decimal point as the sixth
and seventh characters following the colon. For example, the product identier US:AAAEQ3T123XYZ would indicate an REN of 0.3. The REN is used to determine how many devices you may
connect to your telephone line and still have them ring when you are called. In most, but not all areas, the sum of all RENs should be ve (5.0) or less. You may want to contact your local telephone
company for more information.
2.
Connection and use with the nationwide telephone network
The plug and jack used to connect this equipment to the premises wiring and the telephone network must comply with the applicable Part 68 rules and technical requirements adopted by ACTA. A
compliant telephone cord and modular plug is provided with this product. It is designed to be connected to a compatible modular jack that is also compliant. An RJ11 jack should normally be used
for connecting to a single line and an RJ14 jack for two lines. See Installation Instructions in the user’s manual. This equipment may not be used with Coin Telephone Lines or with Party Lines. If
you have specially wired alarm dialing equipment connected to your telephone line, ensure the connection of this equipment does not disable your alarm equipment. If you have questions about
what will disable alarm equipment, consult your telephone company or a qualied installer.
3.
Repair instructions
If this equipment is malfunctioning, it must be unplugged from the modular jack until the problem has been corrected. Repairs to this telephone equipment can only be made by the manufacturer
or its authorized agents. For repair procedures, follow the instructions outlined under the Limited Warranty.
4.
Rights of the telephone company
If this equipment is causing harm to the telephone network, the telephone company may temporarily discontinue your telephone service. The telephone company is required to notify you before
interrupting service. If advance notice is not practical, you will be notied as soon as possible. You will be given the opportunity to correct the problem and the telephone company is required to
inform you of your right to le a compliant with the FCC. Your telephone company may make changes in its facilities, equipment, operation, or procedures that could affect the proper functioning
of this product. The telephone company is required to notify you if such changes are planned.
FCC, ACTA and IC regulations