Filter
Top Products
12
SMT-i3105 SETUP
INITIALIZING THE SMT-i3105
Initially the SMT-i3105 IP keyset will need to be setup to operate within the users
network.The Setup Menu is also used to make changes to the keyset,in the event
that the system information should change.The option chosen will be highlight-
ed.
The station numbers will be automatically created by the OfficeServ 7000 Series
systems once the necessary information has been entered into the IP keyset.
Enter ID and password of the server,as described below to register the phone.See
your system administrator for specific Network and Server addresses.The address-
es necessary to set up the SMT-i3105 are:
• IP Address of Station
• Subnet Mask
• Network Gateway Address
• IP Address of System’s main processor
• User ID
• Password
SETUP MODE
To get to the SETUP MODE unplug the power cord from the SMT-i3105.Press and
hold the
✱✱
button while you plug power back into the phone.Release the
✱✱
but-
ton when you see Samsung in the display.If you have a PoE (Power over Ethernet)
connection, the same procedure can be done by unplugging and plugging the
Ethernet cable into the phone while pressing and hold-
ing the
✱✱
button.
When the phone reboot is complete, the Language
Menu will display.Press the OK soft button to advance to
the Configuration Menu.
Once the Configuration Menu is displayed, you can move to each menu in the
Setup by using the Call Log (
s Up) or Phone Book (t Down) buttons and [1]-[8]
dial buttons of the SMT-i3105 IP phone. To learn how to navigate the menus refer
to the previous section.
smt-i3105_combined_user_guide.qxp 4/26/2010 2:11 PM Page 12
13
EASY INSTALL WIZARD
By selecting this option,the System Easy Wizard can guide you through setting up
your network parameters.If you want to set up these parameters individually,fol-
low the instructions below.
• From the idle phone press Menu, scroll to Settings, and press OK button.
Scroll to Phone Info and press OK button.From the keypad,enter the admin-
istrator’s password (please contact your phone system administrator). Press
the OK button.Scroll to Easy Install and press OK button.
SELECTING THE STATIC IP OPTION
• When the Static IP option is selected,the user enters the Static IP Address for
the phone (eg.192.168.9.193) then press the OK button or the Next soft but-
ton.
• Enter the Subnet Mask (eg.255.255.255.0); press OK button or the Next soft
button.
• Enter Gateway Address (eg.192.168.9.1), press OK button.
NOTE: Press the ✱ key on the dial pad to enter the “.”in the IP address.
• Enter the System IP address (eg.192.168.9.200),press OK button.
• Enter System ID XXXX (eg.3201),then press OK button.
• Enter Password XXXX (eg.1234) then press OK button.
Wait a second for the phone to reboot. The phone should register and authenti-
cate itself to the phone system.Test SMT-i3105 for proper operation.
SETTING UP HOT DESKING [IDLE LOGIN]
Hot Desking allows you to log in and out of your SMT-i3105 IP keyset without
rebooting.S
ee Setup Mode on how to access the Configuration Menu.
• Press the Menu soft button, scroll to Settings then press OK button.
• Scroll to Phone Info and press OK button.
• Enter the administrator’s password (please contact your phone system admin-
istrator).
• Scroll to Ext.Login then press OK button.
• Choose the ON option and press OK button.(Note:ON to allow,OFF to deny
hot desking).
• Press the End soft button to complete the setup.
• When the phone restarts,enter the ID (eg; extension 2809) and password.
• Press the Save soft button to complete the login.
smt-i3105_combined_user_guide.qxp 4/26/2010 2:11 PM Page 13