Filter
Top Products
56
CUSTOMIZING YOUR KEYSET
AME PASSWORD
This feature allows customers using the AME feature to enable password protec-
tion.This will prevent unauthorized users from listening to your messages being
left.The passcode is the same as your station passcode.This feature only applies if
there is a Samsung Voicemail card installed in the system and your keyset has a
programmed AME button.
• With the handset on-hook,press Transfer and then dial 110.
• Dial 101 to turn on AME PASSCODE or 100 to turn it off.
• Press Transfer to store your selection.
AUTO CAMP-ON
This option allows intercom calls to be automatically camped on,if possible,when
a busy station is called.
• With the handset on-hook,press Transfer and then dial 110.
• Press 081 to turn CAMP-ON on or 080 to turn it off.
• Press Transfer to store your selection.
SELECT RING TONE
Each SMT-i3105 user can select from a variety of ring tones.
From the LCD:
• Press Menu button.
• Scroll to Sound option and press OK.
• Select Ring Tone and press OK—OR—you may dial 1 and immediately enter
the option.
• Use Volume Up [+] or Down [-] buttons to scroll through the available ring
tones and press OK or Save soft button to store your selection.
• Press End soft button to return to idle screen.
CHANGE YOUR PASSCODE
From the factory,your station passcode is 1234.You can change your station pass-
code whenever you desire.
• While on-hook,press Transfer and then dial 101.
• Dial your old passcode.
• Dial a new passcode (must be four characters).You can use 0–9.
smt-i3105_combined_user_guide.qxp 4/26/2010 2:12 PM Page 56
57
• Redial the new passcode. If successful, you will hear two beeps. Four beeps
indicate an incorrect code to confirm,reenter the code again.
• Press Transfer to store the new passcode.
SET ANSWER MODE (INTERCOM)
You can receive internal calls in one of three modes (see Answer
ing Intercom Calls
under Int
ercom Calls
for descriptions).
• While on-hook,press Transfer and then dial 103.
• Dial 0 for Ringing,1 for Auto Answer or 2 for Voice Announce.
• Press Transfer to store your selection.
NOTE: When your keyset is programmed for Voice Announce and you have For-
ward No Answer (FNA) turned on,you must answer screened transfers by pressing
the OK button before your FNA timer expires or the call will forward.
SET ANSWER MODE (CO)
Your incoming CO calls can be set to follow the intercom answer mode.
• While on-hook,press Transfer and then dial 110.
• Dial 15 to access AUTO ANS CO.
• Press the Volume Up [+] or Down [-] key to change status (On/Off).
• Press Transfer to store your selection.
AUTOMATIC HOLD
While on an outside call,pressing a line button,route button or a flashing Call but-
ton will automatically put your call on hold and connect you to the next call.This
feature can be turned on or off at your keyset.
• With the handset on-hook,press Transfer and then dial 110.
• Dial 001 to turn Automatic Hold on or 000 to turn it off.
• Press Transfer to store your selection.
HOT KEYPAD
On your phone system your keyset’s keypad can be made “live”or “hot”so that it is
not necessary to lift the handset or press the Speaker button before you begin di-
aling.Calls can be made and features activated by simply dialing the C.O.line num-
ber,trunk group access code,intercom number or feature access code.
• With the handset on-hook,press Transfer and then dial 110.
• Dial 031 to turn the Hot Keypad on or 030 to turn it off.
• Press Transfer to store your selection.
smt-i3105_combined_user_guide.qxp 4/26/2010 2:12 PM Page 57