Filter
Top Products
Sheet 7
To receive a transfer call
When a handset receives a transfer page, it sounds the distinct paging tone and shows CALL TRANSFERRED in
the display. To answer a transferred call, pick up the handset and press [TALK/ash] or [ ]. (If Auto Talk
is on, the phone automatically answers when you pick it up from the cradle; if the handset is already o the
cradle, you can also press any key on the twelve-key dial pad.)
4-5. Adjusting the Speaker Volume
You can change the speaker volume on the base, the handset earpiece, or the handset speakerphone.
On the base
You can choose from ten volume levels ( - ) for the base speaker. Press [vol/select/ ] to make the
volume louder or [vol/select/ ] to make it softer .
Notes:
You can't change the speaker volume when you're using the base setup menu. Exit the menu, and then
change the volume.
If you hear three quick error beeps, it means the speaker is already at the lowest ( ) or highest ( ) volume
level.
On the handset
When you are on a normal call, press [ / ] to make the earpiece louder or [ ] to make it softer.
The handset display shows the current volume level for the earpiece.
When you are using the speakerphone, use [ / ] or [ ] to change the speaker volume. The handset
display shows the current volume level for the handset speakerphone.
There are four volume levels: LOW, MEDIUM, HIGH, and MAXIMUM.
Notes:
The handset earpiece and the handset speakerphone have separate volume settings.
If you hear three quick error beeps, it means the earpiece or speaker is already at the lowest (LOW) or highest
(MAXIMUM) volume level.
4-6. Finding a Lost Handset
To locate a lost handset, press [nd hs] on the base. All registered handsets will beep for sixty seconds.
To cancel paging, press [nd hs] again or press any key on the found handset.
4-7. Muting the Ringer
When the phone is ringing, you can mute the ringer on the base or the handset. Muting stops the ringer for the
current call only: the ringer will sound with the next incoming call.
On the handset
You can only mute the handset ringer if the handset is already o the cradle when the handset starts ringing.
Press [END] to mute the incoming ring.
On the base
Press [ ] to mute both the ringer and the answering system speaker. To turn the ringer back on for this call,
press the [ringer].
Note: When you turn the ringer back on, the answering system speaker is still o; to turn the answering system
speaker back on, press [vol/select/ ] or [vol/select/ ].
4-8. Using an Optional Headset
To install a headset, remove the headset jack cover and insert the headset plug
into the headset jack.
When you connect a headset, the earpiece and speakerphone are automatically
muted. If you want to re-activate the earpiece or speakerphone, remove the
headset plug.
You will still make and receive calls as usual: just use your headset to talk to the
caller once the call connects.
You can purchase headsets from our website at www.uniden.com or by calling
our Parts Department (See the back cover page).
•
•
•
•
•
•
•
•
4-4. Redialing the Last Dialed Number
Pick up the handset from the cradle.
Press [redial/pause].
Press [TALK/ash] or [ ].
1)
2)
3)
Pick up the handset from the cradle.
Press [TALK/ash] or [ ].
Listen for the dial tone.
Press [redial/pause].
1)
2)
3)
4)
OR
5) Using Caller ID and Call Waiting
If you subscribe to Caller ID from your phone company, your phone will show you the caller's phone number and
name (if available) whenever a call comes in. If you subscribe to both Call Waiting and Caller ID, the phone also
shows you the name and the number of any call that comes in while you're on the line.
5/11 12:30PM
Jane Smith
214-555-1234
The date and time received
Caller's name
Caller's Phone Number
Note: If you answer a call before the Caller ID record is received (for example, before the second ring), the Caller
ID record will not appear.
The phone stores the Caller ID information for up to thirty incoming calls - even unanswered calls. If the phone
receives more Caller ID records than it can store, the oldest record in the list is automatically deleted. For
information on storing Caller ID records in the phonebook, see section 6-6.
5-1. Reviewing the Caller ID Record List
You can review the Caller ID list when the handset is in standby or during a call.
Press [cid/menu]. The summary screen displays the total number of
CID records along with the number of new CID records (that is, calls
that you haven't reviewed yet).
Use [ ] to scroll through the records from the latest to the earliest,
or use [ / ] to scroll through the records from the earliest to the
latest.
Press [cid/menu] to exit the Caller ID list.
For new Caller ID records, the phone keeps a count of the number of calls
received from the same caller (instead of saving the information multiple
times). The Caller ID record shows the time and date of the most recent call
from that number, and the number of calls appears next to the received
time. The phone only maintains this count for new or “unviewed” records:
once you review that record, the number is cleared.
1)
2)
3)
Caller ID
New :01
Total:17
Caller ID
New :01
Total:17
12/30 11:59PM 01
Jane Smith
214-555-1234
12/30 11:59PM 01
Jane Smith
214-555-1234