Filter
Top Products
#
C
H
R
E
D
IA
L
V
O
L
/R
IN
G
1
2
ABC
3
DEF
0
OPER
C
A
L
L
S
D
E
L
TA
L
K
M
E
M
F
L
A
S
H
7
PQ
RS
8
TUV
9
W
XYZ
4
G
HI
5
JKL
6
M
NO
Telephone Operation (Cont.)
3. After hearing a dial tone, dial the desired
number.
4. If you misdial, simply press the "TALK"
button, wait for a couple of seconds, and
press the "TALK" button again for a new
dial tone.
5. After your conversation is completed,
press the "TALK" button once to disconnect
1. IF THE HANDSET IS OUT OF THE
CRADLE, press any key on the handset.
2. IF THE HANDSET IS IN THE
CRADLE, lift the handset. DO NOT press
the "TALK" button, as you will be
connected automatically.
When the Phone Rings
When the handset is not in the base, only a
handset having the identical security code
and operating on the same channel can
access the base and use your phone line.
When the handset is in the base, no other
handset, even those having the identical
security code and operating on the same
channel, can access the base and use your
line.
Digital security coding will also eliminate
the "false" ringing associated with cordless
telephones not equipped with this feature.
Your cordless telephone has 40 operating
channels. The phone will automatically
search and select the clearest channel when
you pick up the handset and press the
"TALK" button. If you hear noise or other
interference during your conversation, you
can manually select a clearer channel by
pressing and releasing the channel control
on the handset to switch to another spare
channel. Your call will not be interrupted.
40 Channel Operation
Note:
of range, you may lose the call. If this
occurs, place the handset back into the base
for ten seconds to reset the security code
and then make the call again.
MakingaCall
CALLS
DEL
MEM
FLASH
TALK
Receiving a Call Through the
Handset
the line, or return the handset to the base.
Receiving Call Through the Base
Press the "SPEAKER" button on the base unit.
You can speak through the microphone, without
lifting the handset or press the "TALK" Button
on the handset. H/S display will show "LINE
IN USE". Press the "SPEAKER" button again to
terminate a call.
The unit will beep and you can now make
the call. If that does not work, make sure
DC adaptor is connected. If necesssary,
unplug theDC adaptor from the power
source. Disconnect the battery for 5 seconds
and then reconnect. Place the handset on the
base and then replug the DC adaptor (see
Troubleshooting). Let stand 2 minutes
before use.
If you experience static while using the
telephone, move closer to the base or
change the channel by pressing the "CH"
button on handset.
Out of Range
Telephone Operation (Cont.)
You can connect a headset (not included)
for hands-free conversations.
1. Insert the headset plug (must be 3/32 inch/
2.5mm type) into the headset jack on the side
of the handset.
2. Attach the belt clip to the back of the
handset. Make sure the "arms" of the belt clip
snap securely into the notches on the side of
the handset. You can now attach the handset/
belt clip to the desired location on your
clothing.
3. Adjust the headset microphone to a
comfortable position, placing it near your
mouth.
4. Press the "TALK" button to make or
receive a call.
Headset Jack
Note:
-When the belt clip is connected to the
handset, the handset can not charge on
the base.
-You can purchase a headset through our
help line at 1-800-366-0937, our secure
website at
http://www.swbfreedomphone.com, or
your local retailer.
5. To remove the belt clip from the
back of the handset, use your fingernails
to loosen one of the "arms" of the belt
clip. The other "arm" of the belt clip
will automatically release from the
handset.
Note:
If you experience difficulty with placing or
receiving calls, lost security code may be the
cause of the problem. When this occurs, the
handset can no longer communicate with its
base. The loss of the code can occur any of
the following ways: the battery is drained and
needs recharging; the DC adaptor is
disconnected or a power loss has occurred;
or anything that causes electrical
interference, for example, multiple cordless
telephones, baby monitors, televisions,
VCR's etc. Reset the security code by
placing the handset on the base for 10
seconds, removing it from the base, then
replacing it on the base for an additional
10 seconds.
#
C
H
R
E
D
I
AL
V
O
L
/R
IN
G
1
2
A
B
C
3
D
E
F
0
O
P
E
R
C
A
L
L
S
D
E
L
TA
L
K
M
E
M
F
L
AS
H
7
P
Q
R
S
8
T
U
V
9
W
X
Y
Z
4
G
H
I
5
JK
L
6
M
N
O
#
C
H
R
E
D
IA
L
V
O
L
/R
IN
G
1
2
ABC
3
DEF
0
O
PER
C
A
L
L
S
D
E
L
TA
L
K
M
E
M
F
L
A
S
H
7
PQRS
8
TU
V
9
W
XYZ
4
GHI
5
JKL
6
MNO
13
14
1. Lift the handset and press the "TALK"
Button to be connected to the phone line.
The handset display will show TALK.
The base display will show LINE IN USE
You must be within maximum range to
change channel. If you come close to being
out