Filter
Top Products
Installation (Cont.)
Note : To maximize your battery's life, we
recommend that you periodically fully drain
thebatteryandthenrechargeit.Todothis,
unplug your phone line cord from your wall
phone jack. Press the "TALK" button and
allow the handset to remain on for 10 to 12
hours. Return the handset to the base and
allow to fully charge for 12 hours. If this
process is completed monthly, it will reduce
To Set Area Code
Caller ID Setup
To Replace Batteries:
1. Remove battery
cover.
2. Remove old battery.
3. Install new battery.
4. Close battery cover.
Charge 10-14
hours before first
use.
Tone/Pulse Switch
1. If your house is wired for rotary
service, move the Tone/Pulse (T/P)
switch to the Pulse position (P).
2. If your house is wired for Touch Tone
service, move the T/P switch to the
Tone position (T).
3. If you are not certain which type of
dialing service you have, set the switch to
Tone (T). On the handset, press the TALK
button and then any digit on the keypad. If
the dial tone persists, switch to Pulse (P).
To disconnect, press TALK again, or set the
handset in the cradle.
Note:
1. The Caller ID setup procedure will not
begin until the handset has been fully
charged for 10-14 hours.
4. If you delay more than 20 seconds in
between any of the above steps, the unit will
revert to the beginning of the setup procedure.
5. To adjust the handset LCD display contrast
while in the standby mode, press the "FLASH"
button. Then press the " *" or "# " button
to set the desired contrast. Press "MEM" button
to confirm the contrast level.
Caller ID Setup/Telephone Operation
Digital Security System
with a digital security coding system to
protect your base unit from being accessed
by other cordless telephones.
The code allows your base and handset to
recognize each other so that other cordless
phones will not make calls on your line.
If the DCadaptor is disconnected or a loss
of power occurs while the handset is away
from the base unit, the security code will be
lost and the phone will be inoperable. If
this occurs, reconnect the DCadaptor and
return the handset to the base unit so that the
security code is reset. The base will beep to
confirm that the security code has been reset.
2. Press the "MEM" button to confirm the
displayed contrast level. The time and date
will be automatically updated when the first
Caller ID call is received.
Tone/PulseSwitch
1. Press the " *" or "# " button to adjust
the display contrast to the desired level
(lighter or darker).
To Set Handset Display Contrast
2. To set up your GH3060 again, press the
"CH" Button for a second in the Date/Time
screen.
3. Your GH3060 will always stay in setup mode
until you complete area code setup steps.
The GH3060 will operate on tone or rotary
systems.
Your GH3060 Cordless Telephone is equipped
11
12
T/P
RINGER
ON/OFF
DC10V650mA
USEONLY WITH CLASS 2 POWER SOURCE
-
+
the memory buildup that occurs from
partial charging.frequent
Note: In order that the Caller ID Redial feature
works properly, you must set your local area code.
1. After installing the FULLY CHARGED handset
battery, the handset display will light and will
show "AREA CODE?"
2. Enter your 3-digit local area code using the
handset keypad.
3.After entering the third digit, press the "MEM"
button to confirm the displayed area code. The
unit will return to Date/Time Screen.
1. Press the "CH" button for a second in Date/Time
screen. The display will light and show "SET
LANGUAGE"
2.You can choose to see your LCD indications in
English, French or Spanish. Press the " *" or
"# " button to choose the desired language.
3. Press the "MEM" key to confirm the display
language. The unit will begin to set the area code.
4. Set your local area code according to the above
steps ( To Set Area Code ). Once finished, the unit
will begin to set the remote access PIN code. Press
the "MEM" button to skip the setting (PIN code
not applicable in the GH3060 model). The unit
will begin to set the handset display contrast level.
To Set Language
▲
▼
Telephone Operation
BACKLIGHT
BRIGHT/ NORMAL / OFF