Filter
Top Products
31
Appendix
FCC Part 15
This equipment has been tested and found to comply with the requirements for a Class B digital device under
Part 15 of the Federal Communications Commission (FCC) rules. These requirements are intended to provide
reasonable protection against harmful interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one by turning the equipment off and on, the user is encouraged to try to correct the interference by oneby turning the equipment off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Changes or modications to this equipment not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device
may not cause harmful interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation. Privacy of communications may not be ensured when using this telephone.
To ensure safety of users, the FCC has established criteria for the amount of radio frequency energy that can be
safely absorbed by a user or bystander according to the intended usage of the product. This product has been tested
and found to comply with the FCC criteria. The handset may be safely held against the ear of the user. The telephone
base shall be installed and used such that parts of the user’s body other than the hands are maintained at a distance
of approximately 20 cm (8 inches) or more. If you choose to use a clipping device, please make sure to only use the
supplied VTech belt clip.
This Class B digital apparatus complies with Canadian ICES-003.
FCC Part 68 and ACTA
This equipment complies with Part 68 of the FCC rules and with technical requirements adopted by the Administrative
Council for Terminal Attachments (ACTA). The label on the back or bottom of this equipment contains, among other
things, a product identier in the format US:AAAEQ##TXXXX. This identier must be provided to your local telephone
company upon request.
The plug and jack used to connect this equipment to premises wiring and the telephone network must comply with
applicable Part 68 rules and technical requirements adopted by ACTA. A compliant telephone cord and modular plug
is provided with this product. It is designed to be connected to a compatible modular jack that is also compliant. An
RJ11 jack should normally be used for connecting to a single line and an RJ14 jack for two lines. See Installation
Instructions in the user’s manual.
The Ringer Equivalence Number (REN) is used to determine how many devices you may connect to your telephone
line and still have them ring when you are called. The REN for this product is encoded as the 6th and 7th characters
following the US: in the product identier (e.g., if ## is 03, the REN is 0.3). In most, but not all areas, the sum of all
RENs should be ve (5.0) or less. For more information, please contact your local telephone company.
This equipment may not be used with Party Lines. If you have specially wired alarm dialing equipment connected
to your telephone line, ensure the connection of this equipment does not disable your alarm equipment. If you have
questions about what will disable alarm equipment, consult your telephone company or a qualied installer.
If this equipment is malfunctioning, it must be unplugged from the modular jack until the problem has been
corrected. Repairs to this telephone equipment can only be made by the manufacturer or its authorized agents. For
repair procedures, follow the instructions outlined under the Limited Warranty.
If this equipment is causing harm to the telephone network, the telephone company may temporarily discontinue your
telephone service. The telephone company is required to notify you before interrupting service. If advance notice is
not practical, you will be notied as soon as possible. You will be given the opportunity to correct the problem and the
telephone company is required to inform you of your right to le a complaint with the FCC. Your telephone company
may make changes in its facilities, equipment, operation, or procedures that could affect the proper functioning of this
product. The telephone company is required to notify you if such changes are planned.
If this product is equipped with a corded or cordless handset, it is hearing aid compatible.
If this product has memory dialing locations, you may choose to store emergency telephone numbers (e.g., police,
re, medical) in these locations. If you do store or test emergency numbers, please:
Remain on the line and briey explain the reason for the call before hanging up.
Perform such activities in off-peak hours, such as early morning or late evening.
•
•
•
•
FCC, ACTA and IC regulations