Filter
Top Products
8. Press [Down] or [PREV] to decrease the setting, [UP] or [NEXT] to
increase the setting, or use the dial pad to key in the value (press [1] for
AM and [2] for PM). The default time/date setting is 12:00 am 1/01. The
range of Time/date settings is 12:00am 1/01 – 11:59pm 12/31. The local
clock will also be updated automatically when a caller ID is received.
9. Press [DIAL/ENTER] or [MENU] to advance to next
setting. The display will show “TONE DIALING” with
“Tone” flashing, if it is still set to the default.
10. Press [Down], [PREV], [UP] or [NEXT] to switch from Tone to “PULSE
DIALING.” The default setting is Tone.
Note: If you are unsure which type of phone system you have, set it to
Tone. If this setting does not work, change the setting to Pulse.
11. Press [DIAL/ENTER] or [MENU] to advance to next
setting. The display will show “FLASH TIME = msec”
and the current flash setting.
12. Press [Down] or [PREV] to decrease the setting, [UP] or [NEXT] to
increase the setting in increments of 100msec, or use the dial pad to key
in the value. The default setting is 600msec. The range of flash time
settings is 100msec – 1500msec.
13. Press [DIAL/ENTER] or [MENU] to advance to next
setting. The display will show “RINGER 1 TONE” with
the current ringer tone number flashing above it.
14. Press [Down], [PREV], [UP] or [NEXT] to increase or decrease the ringer
tone on line 1. The range of ringer tone settings is 1-8.
15. Press [DIAL/ENTER] or [SAVE] to choose the next line.
The display will show “RINGER 2 TONE” with the
current setting flashing above it. Repeat the same
procedure for the other three lines.
16. Press [DIAL/ENTER] or [MENU] to advance to next
setting. The display will show “RINGER 1 ON.”
17. Press [Down], [PREV], [UP] or [NEXT] to switch
between Line 1 ring On and Line 1 ring Off. The default setting is all lines
on.
18. Press [DIAL/ENTER] or [SAVE] to advance to next
setting. The display will show “RINGER 2 ON.”
16
Programming the Telephone Settings
You may need to go through most of the settings, even if you only to need to
change some of the settings. At any time during telephone programming,
press [DIAL/ENTER] or [SAVE] to save the new settings and advance to the
next one, press [MENU] to save and skip to the next setting group, press
[DEL] to go back to the previous setting group, or press [QUIT] to leave the
telephone programming menu.
1. Press [MENU]. The display will say “SET CONTRAST”
and the current contrast setting will flash.
2. Press [Down] or [PREV] to decrease the setting, [UP] or [NEXT] to
increase the setting, or use the dial pad to key in the value. The default
setting is 3. The range of contrast settings is 1-5.
3. Press [DIAL/ENTER] or [MENU] to advance to next
setting. The default setting is “PRIORITY = AUTO.”
4. Press [Down] or [PREV] to decrease the setting, [UP]
or [NEXT] to increase the setting, or use the dial pad to key in the value
(press [5] for auto priority). The range of priority line settings is line
1/2/3/4/auto.
Note: If the priority line is set to line 1 for example, Caller ID for line 1 will
have priority, message waiting [VMI] on line 1 is enabled, and VMI
on line 2, 3, & 4 is disabled. If the priority line is set to auto, the
telephone will allocate priority to a line automatically depending on
need. Message waiting [VMI] on all lines are disabled on auto
priority.
5. Press [DIAL/ENTER] or [MENU] to advance to next
setting. The default setting is “HEADSET OFF.”
6. Press [Down], [PREV], [UP] or [NEXT] to switch between Headset On and
Headset Off.
Note: If the headset is enabled (Headset On), the speakerphone will be
disabled.
7. Press [DIAL/ENTER] or [MENU] to advance to next
setting. The display will show “SET TIME/DATE.” The
current time and date setting will display with the hour flashing.
TELEPHONE SETUP
15
SET CONTRAST
3
FLASH TIME = MSEC
600
TONE DIALING
RINGER 1 ON
RINGER 1 TONE
RINGER 2 TONE
PRIORITY = AUTO
HEADSET OFF
SET TIME/DATE
3:27
PM
1/18
TELEPHONE SETUP
RINGER 2 ON