Filter
Top Products
SYSTEM RESET – PROGRAMMING SAVED
P+ >
R1.0
PII >
R1.0
(p. 5-138)
(p. 5-181)
IMPORTANT: Using this procedure disconnects any active calls but retains system settings. Use it only if the system fails to
function correctly after a power failure or down period.
DIAL #728
Dialing Restrictions and Permissions
OUTGOING CALL RESTRICTION
P+ >
R1.0
(p. 5-109)
PII >
R1.0
(p. 5-144)
DIAL #401
DIAL an extension number (10-33
P+, 10–57 PII)
DIAL 1 = No Restriction ✔
2 = Inside (intercom) Only
3 = Local (intercom and
local) Only
PRESS [
Next Item
] to program
another extension
P+ >
R1.0
PII >
R1.0
(p. 5-41)
(p. 5-71)
P+ >
R1.0
PII >
R1.0
(p. 5-50)
(p. 5-82)
TOLL CALL PREFIX
P+ > R1.0
PII >
R1.0
DIAL #402
(p. 5-143)
(p. 5-186)
DIAL 1 = 0/1 plus Area Code and
Number ✔
2 = Area Code and Number
Only
LISTS
P+ >
R1.0
PII >
R1.0
(p. 5-9)
(p. 5-9)
P+ >
R3.1
PII >
R3.1
(p. 5-60)
(p. 5-92)
DISALLOWED LIST ASIGNMENTS
P+ >
R1.0 (p. 5-40)
PII >
R1.0
(p. 5-70)
SYSTEM PASSWORD
P+ >
R1.0
PII >
R1.0
(p. 5-137)
(p. 5-180)
DIAL #403
DIAL four digits to set the password
DISALLOWED PHONE NUMBER
LISTS
DIAL #404
DIAL a list number (1–4)
DIAL a list entry (01–10)
To add entry:
DIAL the telephone number (up to
12 digits)
PRESS [
Enter
]
PRESS [
Remove
] to remove a list entry
PRESS [
Next Item
] to program another
list entry
To program another list:
PRESS [
Next Procedure
] [
Prev Procedure
],
enter a new list number, and
repeat above steps
DIAL #405
DIAL an extension number (10-33
P+, 10–57 PII)
DIAL a list number (1–4)
DIAL 1 = Assigned
2 = Not Assigned ✔
PRESS [
Next Item
] to assign another
list
To program another extension:
PRESS [
Next Procedure
] [
Prev Procedure
],
enter a new extension
number, and repeat above
steps
EMERGENCY PHONE NUMBER
LIST
DIAL #406
DIAL a list entry (01–10)
To add entry:
DIAL the telephone number (up to
12 digits)
PRESS [
Enter
]
PRESS [
Remove
] to remove a list entry
PRESS [
Next Item
] to program another
list entry
ALLOWED PHONE NUMBER
DIAL #407
DIAL a list number (1–4)
DIAL a list entry (01–10)
To add entry:
DIAL the telephone number (up to
12 digits)
PRESS [
Enter
]
PRESS [
Remove
] to remove a list entry
PRESS [
Next Item
] to program another
list entry
To program another list:
PRESS [
Next Procedure
] [
Prev Procedure
],
enter a new list number, and
repeat above steps
ALLOWED LIST ASSIGNMENTS
P+ >
R1.0
(p. 5-8)
PII > R1.0
(p. 5-80)
DIAL #408
DIAL an extension number (10-33
P+, 10-57 PII)
DIAL a list number (1–4)
DIAL 1 = Assigned
2 = Not Assigned ✔
PRESS [
Next Item
] to assign another list
To program another extension:
PRESS [
Next Procedure
] [
Prev Procedure
],
enter a new extension
number, and repeat above
steps
FORCED ACCOUNT CODE LIST
DIAL #409
DIAL a list entry (01–99)
To add entry:
DIAL the account code (up to
6 digits)
PRESS [
Enter
]
PRESS [
Remove
] to remove a list
entry
PRESS [
Next Item
] to program
another list entry
CLEAR – SYSTEM RESET – PROGRAMMING NOT
SAVED
P+ >
R1.0
PII >
R1.0
IMPORTANT: Using this procedure disconnects any active calls and ERASES all system and station programming back to the
factory settings.
DIAL #989 or 25327
System Speed Dial Numbers
P+ R1.0–R3.1: 60 SS w/2 Digit Codes 20-79, > R4.0 100 SS w/3 Digit Codes 600-699
PII R1.0–R3.1: 60 SS w/2 Digit Codes 20-79, >
R4.0 100 SS w/3 Digit Codes 600-699
(p. 5-139)
(p. 5-182)
To program a number:
PRESS [
Feature
] [
0
] [
0
] to enter programming mode
To remove a number:
PRESS [
Feature
]
PRESS [
Feature
] [
0
] [
0
] to enter programming mode
DIAL a three-digit code (600–699)
PRESS [
Feature
]
DIAL the telephone number—up to 28 digits (20 prior to R4.0) including
DIAL the System Speed Dial number’s code (600–699)
special characters (see page 5-127 P+, 5-164 PII) To “mark” it (to
PRESS [
Mic
]
override restrictions), dial [ ★ ] before the telephone number
To remove another number, repeat
To program another number, or to change a number, repeat
PRESS [
Feature
] [
0
] [
0
] to exit programming mode
l
l
l
l
l
l
PRESS [
Feature
] [
0
] [
0
] to exit programming mode
✔
= Factory setting
= Button with lights required
= Indicates release when feature was first added to system e.g. >
R3.0
P+/PII R4.1
7