Filter
Top Products
AM
AMAM
AM
AM
AM
SETTING UP YOUR FM2552PX
DO NOT CONNECT the line cord to the wall outlet until the Caller ID
setup has been completed.
To Set Language
1. The LCD shows ‘ENTER LANGUAGE’
followed by a choice of 3 languages (English,
Spanish, French). If your display does not appear
this way, press and hold both and buttons for 4 seconds.
2. The LCD then shows ‘ENG ESP FRA’.
The ‘ENG’ is BLINKING. Press or button
to select ‘ENG’, ‘ESP’, or ‘FRA’. Press ERASE
button to confirm.
To Set Contrast Level
1. If ENG is selected, the LCD shows ‘LCD
CONTRAST’.
2. Press or button to adjust five levels (from 1
to 5, default is 3) contrast of LCD.
3. Press ERASE button to confirm.
To Set Area Code
1. If contrast is set, the LCD shows ‘ENTER AREA
CODE’. The first digit ‘–’ of the area code will
blink.
2. Press or button to enter the area code. Press ERASE button to
confirm and go to next entry.
3. Repeat above steps until 3-digit area code is set.
To Set Time/Date
1. If area code is set, the LCD shows ‘ENTER
TIME DATE’.
2. Press or button to select the hour digits.
3. Press ERASE button to confirm and go to the next entry.
4. Press or button to select the minute digits.
5. Press ERASE button to confirm and go to the
next entry.
6. Press or button to select the month digits.
7. Press ERASE button to confirm and go to the
next entry.
8. Press or button to select the date digits.
9. Press ERASE button to confirm.
The LCD shows ‘TOTAL:00 NEW:00’, which
means both the total call and new call counter are
zero.
TELEPHONE FEATURES
NOTE: Batteries must be installed, or Telephone operations will not
work properly (see Installation).
TONE/PULSE SWITCH
Set switch to your type of service. If you don’t know whether you have
tone or pulse:
1. Put the switch on “T”.
2. When you have a dial tone, press any key on the keypad. If the dial
tone stops, leave it on “T”. If not, change the setting to “P”.
Mixed Dialing:
Mixed dialing is useful to subscribers of Pulse (rotary) service who wish
to gain access to various low-cost long-distance or automated computer
services otherwise not available to them.
1. With the T/P switch in the P position, dial the phone number.
2. Press
*
button, and your telephone will change to TONE dialing mode.
3. Dial your code/authorization number. When your call is completed,
your telephone will automatically return to the PULSE dialing mode.
NOTE: Mixed dialing can also be stored into the memory for one-touch
access to your long distance or automated computer service.
RECEIVING A CALL
1. When your phone rings, pick up the handset and use it like any basic
telephone. After the second ring, the caller’s name and telephone
number will display if you have Caller ID service. The NEW CALL
LED and the NEW CALL icon will flash. The Caller ID information
will be stored in the order received.
2. Hang up the handset to release the telephone line when your
conversation is completed.
DIALING A CALL
1. Pick up the phone and wait for a dial tone.
2. Press the keypad for the telephone number you wish to dial. The display
will show the dialed number.
RECEIVER VOLUME CONTROL
The receiver volume control is located on the side of the handset of your
phone. This enables you to adjust the receiver volume from Normal to
High for a better listening level.
RINGER OFF/LOW/HIGH
Your FM2552PX features a harmonic dual tone ringer that can be adjusted
from a loud (HI) to a soft (LO) sound level. When you don’t want to be
disturbed, slide the switch to the OFF position. You can still make outgoing
calls without being disturbed by incoming calls.
PAUSE
Whether you have Tone or Pulse service, you can insert a 4-second PAUSE
into the dialing or storing of a number into memory in order to access
custom and telebanking services, long distance, etc. Press REDIAL button
at the desired point in the number. Press REDIAL button again if an
additional 4 seconds is needed.
— 10 — — 11 — — 12 —
SETTING UP YOUR FM2552PX TELEPHONE FEATURES