Filter
Top Products
16
TELEPHONE OPERATION (CONT.)
40 Channel AutoScan
Operation
Your cordless telephone has 40
operating channels. The phone will
automatically search and select the
clearest channel when you press the
TALK button. If you hear noise or other
interference during your conversation,
you can manually select a clearer
channel by pressing and releasing the
CH button on the handset to switch to
another spare channel. Your call will not
be interrupted.
NOTE:
You must be in usable range to change
channels. If you press the CH button
when you are close to being out of
range, you may lose the call. If this
occurs, place the handset back into the
base for a few seconds to reset the
security code and then make the call
again.
Receiver Volume Control
Your telephone allows you to adjust the
handset volume to a more comfortable
listening level. Slide the RECEIVER
VOLUME CONTROL on the side of the
handset to NORM, MID or HIGH.
Making a Call
1. Make sure the base antenna is in
upright position.
2. Lift the handset and press the TALK
button to be connected to the phone line.
The handset LCD display will show “TALK”
and the TALK timer will start. The base
LCD display will show “LINE IN USE”.
3. After hearing a dial tone, dial the
desired number.
Or you may predial the number (without
pressing the TALK button), then press
the CALLS button.
4. If you misdial, simply press the TALK
button, wait for a couple of seconds, and
press the TALK button again for a new
dial tone.
5. After your conversation is
completed, press the TALK button once
to disconnect the line, or return the
handset to the base.
Receiving a Call
When the phone rings:
1. IF THE HANDSET IS OUT OF THE
CRADLE, press the TALK button.
2. IF THE HANDSET IS IN THE
CRADLE, lift the handset. DO NOT press
the TALK button, as you will be
connected automatically.
Temporary Tone (*):
In Pulse dialing mode, you can access
bank facilities, telephone answering
machines, etc., by simply pressing the
TONE( * ) key to get into the tone mode
and input the required tone codes. It will
reset automatically after you end your call.
17
TELEPHONE OPERATION (CONT.)
NOTE:
If you experience difficulty with placing or
receiving calls, the lost security code
may be the cause of the problem. When
this occurs, the handset can no longer
communicate with its base. The loss of
the code can occur any of the following
ways: if the battery is drained and needs
recharging; the handset is out of range
of the base unit; the AC adaptor is
disconnected or a power loss has
occurred; or anything that causes
electrical interference, for example
multiple cordless telephones, baby
monitors, televisions, VCR’s etc. Reset
the security code by placing the handset
on the base for 10 seconds. If that does
not work, make sure the AC adaptor is
connected. If necessary, unplug the AC
adaptor from the power source.
Disconnect the battery for 5 seconds and
then reconnect. Place the handset on the
base and then replug the AC adaptor
(see Troubleshooting).
Ringer Control
If you do not want the unit to ring, set the
RINGER switches on the side of the
handset and on the rear of the base to
OFF. The handset and base will no
longer ring when a call is being received.
The LCD display will show “RINGING”
when a call comes in.
Out of Range
If you try to place a call when you are too
far away from the base, you will hear static.
If this occurs, move closer to the base.
Flash
You can use your cordless telephone
with special services such as Call
Waiting or Three Way Calling (Special
subscription from your local telephone
company is required). During a
telephone conversation, you may hear a
tone or click, which indicates that you are
receiving another call. To speak to the
second caller and put the first caller on
hold, press the FLASH button. Press
FLASH button again to return to the
original call. You may also press the
FLASH button to obtain a new dial tone.
Redial
Your telephone remembers the last
number dialed.
1. Press the TALK button on the
handset. When you hear a dial tone,
press the REDIAL button. Or
2. Press the REDIAL button, the last
number will be shown on the LCD
display. Press the CALLS button.
Pause
You can insert a 4-second PAUSE into
the dialing of long distance numbers.
Press the REDIAL button on the handset
during dialing.