Filter
Top Products
12
Installation
If the dial tone stops, you have touch-tone
service. If the dial tone continues, you have
pulse service.
To set the dial mode, press
TALK
to hang up
the phone if necessary, then hold down
FLASH
until the phone beeps and the current
dialing mode, tone or pulse, appears. Then
press
#
to set pulse mode or
∗
to set tone
mode. The phone beeps and displays
Fkbi[
Fkbi[Fkbi[
Fkbi[
:_Wb_d]
:_Wb_d]:_Wb_d]
:_Wb_d]
or
Jed[ý:_Wb_d]
Jed[ý:_Wb_d]Jed[ý:_Wb_d]
Jed[ý:_Wb_d]
, then the display clears.
Note:
The phone exits setting mode if a call
or page is received, or if you press
TALK
.
If the battery pack power gets too low, the
dial mode might reset to tone. If you are on a
pulse line and cannot make a call, try setting
the dialing mode to pulse.
SETTING THE HANDSET’S
RINGER TONE/VOLUME
You can select one of four different ringer
tone/volume settings on the handset. At any
time, except during a call, repeatedly press
VOL/CID
8
88
8
or
9
99
9
to select the desired ringer
setting. Each time you press a button, the
phone rings at the selected setting and
H_d][h
H_d][hH_d][h
H_d][h
7ý>_]^
7ý>_]^7ý>_]^
7ý>_]^
,
H_d][hý7ýBem
H_d][hý7ýBemH_d][hý7ýBem
H_d][hý7ýBem
,
H_d][hý8ý>_]^
H_d][hý8ý>_]^H_d][hý8ý>_]^
H_d][hý8ý>_]^
, or
H_d][hý 8
H_d][hý 8H_d][hý 8
H_d][hý 8
Bem
BemBem
Bem
appears.
You can also turn off the ringer. At any time,
except during a call, hold down
VOL/CID
9
99
9
until the phone beeps and
H_d][hýE\\
H_d][hýE\\H_d][hýE\\
H_d][hýE\\
appears.
When you place the handset faceup on the
base,
2H_d][hýE\\4
2H_d][hýE\\42H_d][hýE\\4
2H_d][hýE\\4
appears.
You can still make or receive a call even
when the ringer is turned off. When you have
an incoming call, any other phone connected
to the same line rings, and
?dYec_d]ý 9Wbb
?dYec_d]ý 9Wbb?dYec_d]ý 9Wbb
?dYec_d]ý 9Wbb
ap-
pears on the handset’s display.
To turn the ringer back on, simply press
VOL/
CID
8
88
8
or
9
99
9
. The ringer is restored at the
RINGER A HIGH setting.
TURNING THE BASE’S
RINGER ON/OFF
You can set the base’s ringer to high or low,
or turn it off. At any time, except during a call,
press
SET/RING
. Each time you press the
button, the phone rings at the selected set-
ting (or does not ring at the OFF setting). The
display shows
>_
>_>_
>_
,
Be
BeBe
Be
, or
E
EE
E\
\\
\
. When you set the
ringer to off, the RINGER OFF indicator
lights.
Even when you turn off the base’s ringer, you
can still make or receive calls using this
phone. Telephones on the same line (and
the handset if it is away from the base and its
ringer is turned on) still ring when there is an
incoming call.
You can also set the ringer in the menu set-
ting mode (see “Using the Menu Button” on
Page 23).
1. Press
MENU
four times. The phone
announces “Ringer volume” followed by
its current setting. The display also
shows the current setting.
2. Press
SET/RING
to enter the setting
mode.
3. Press
SKIP
or
REPEAT
to change the
setting.
4. Press
SET/RING
to store the setting.
5. Press
STOP
to exit the menu setting
mode.
SETTING AUTO TALK
Your phone is preset with Auto Talk off, so
you must press
TALK
to answer a call. With
Auto Talk turned on, you can answer a call
by lifting the handset from the base or, if the
handset is away from the base, by pressing
any key.