Filter
Top Products
14
Installation
Note:
The phone exits setting mode if a call
or page is received, or if you press
LINE
1
or
LINE
2
.
ADJUSTING THE RINGER
The phone lets you control its base and
handset ringer volume separately. You can
choose from a high or low ringer setting or
turn the ringer off for the base and the hand-
set.
On the Handset
In the standby mode, press
DEL
/
VOL
to set
the handset’s ringer volume. The display
shows
H_d][h
H_d][hH_d][h
H_d][h
>_]^
>_]^>_]^
>_]^
or
H_d][h
H_d][hH_d][h
H_d][h
Bem
BemBem
Bem
.
You can also turn off the ringer. In the stand-
by mode, press and hold
DEL
/
VOL
until the
phone beeps and
H_d][h
H_d][hH_d][h
H_d][h
E\\
E\\E\\
E\\
appears. When
you place the handset face-up on the base,
2H_d][hýE\\4
2H_d][hýE\\42H_d][hýE\\4
2H_d][hýE\\4
appears.
You can still make or receive a call even
when the ringer is turned off. When you have
an incoming call, the base unit (if you have
not set
RING
VOL
to
OFF
) and any other
phone connected to the same line rings, and
â9Wbbá
â9Wbbáâ9Wbbá
â9Wbbá
appears on the handset’s display.
To turn the ringer back on, simply press
DEL
/
VOL
. The ringer is restored at the
H_d][h
H_d][hH_d][h
H_d][h
>_]^
>_]^>_]^
>_]^
setting.
On the Base
Set
RING
VOL
on the back of the base to
HI
,
LO
, or
OFF
for each line (
L1
and
L2
). With
RING
VOL
set to
OFF
, the base’s ringer does
not sound when a call is received, but the
handset (when it is off the base with the ring-
er not turned off) and any other phone con-
nected to the same line still ring.
SETTING AUTO TALK
Your phone is preset so you must press
LINE
1
or
LINE 2
to answer a call. With auto talk
turned on, you can answer a call by lifting the
handset from the base (or any key on the
handset if the handset is away from the
base).
Note:
Auto talk is set for each line separate-
ly. For example, when you turn auto talk on
for Line 1 only, you must press
LINE
2
to an-
swer a call on line 2.
Follow these steps to turn auto talk on or off.
1. Lift the handset and hold down
CID
/
HOLD
until
9Wbb[h
9Wbb[h9Wbb[h
9Wbb[h
?:
?:?:
?:
I[jkf
I[jkfI[jkf
I[jkf
appears on the
display with the pointer at
B_d[
B_d[B_d[
B_d[
'
''
'
.
2. Use
∗
∗∗
∗
/
TONE
/
6
66
6
or
#
/
7
77
7
to select
B_d[
B_d[B_d[
B_d[
'
''
'
or
B_d[
B_d[B_d[
B_d[
(
((
(
. Then press
CONF
/
9
99
9
.
3. A menu appears with
7kje
7kje7kje
7kje
JWba
JWbaJWba
JWba
selected.
Press
SELECT
/
CH
to change the setting.
Ed
EdEd
Ed
or
E\\
E\\E\\
E\\
appears indicating the selected
setting.
4. Press
CID
/
HOLD
and return the handset
to the base.
SETTING CALLER ID/CALL
WAITING
If you have Call Waiting and Caller ID ser-
vice, you can set the phone to show Caller ID
information for an incoming call even while
you are already on the phone.
Note:
Caller ID/Call Waiting function is set
for each line separately.
1. Lift the handset and hold down
CID
/
HOLD
until
9Wbb[h
9Wbb[h9Wbb[h
9Wbb[h
?:
?:?:
?:
I[jkf
I[jkfI[jkf
I[jkf
appears on the
display with
B_d[
B_d[B_d[
B_d[
'
''
'
selected.
2. Use
∗
∗∗
∗
/
TONE
/
6
66
6
or
#
/
7
77
7
to select
B_d[
B_d[B_d[
B_d[
'
''
'
or
B_d[
B_d[B_d[
B_d[
(
((
(
. Then press
CONF
/
9
99
9
.