Filter
Top Products
30
|
KCA-BT300
Appendix
About the Cell-Phone
This unit conforms to the following Bluetooth
specifications:
Version Bluetooth Standard Ver. 2.1 + EDR
Profile HFP (Hands Free Profile)
OPP (Object Push Profile)
PBAP (Phonebook Access Profile)
SYNC (Synchronization Profile)
For the cell-phones verified for compatibility, access
the following URL:
http://www.kenwood.com/cs/ce/bt/
⁄
• The units supporting the Bluetooth function have been
certified for conformity with the Bluetooth Standard
following the procedure prescribed by Bluetooth
SIG. However, it may be impossible for such units to
communicate with your cell-phone depending on its type.
About the Bluetooth Audio player
This unit conforms to the following Bluetooth
specifications:
Version Bluetooth Standard Ver. 2.1 + EDR
Profile A2DP (Advanced Audio Distribution Profile)
AVRCP (Audio/Video Remote Control Profile)
About Bluetooth Icons
The control unit supporting the icon display function
can display the following statuses:.
• Bluetooth cell-phone connection status
BT : This indicator turns on when a cell-phone is
connected.
• Signal strength of cell-phone
Maximum
Minimum
• Battery level of cell-phone
Full Nearly dead
⁄
• Icons are not displayed if information cannot be obtained
from the cell-phone.
• Since the number of steps of the control unit is different
from that of the cell-phone, the statuses displayed on the
control unit may discord from those displayed on the cell-
phone.
Menu Glossary
• "D-STATUS"/ "P-STATUS" (Displaying the
Bluetooth device Status)
You can display the connection status, signal
strength, and battery level.
"HF CONNECT"/ "BT-CON" / "HF-CON":
Bluetooth cell-phone connection status.
"AD CONNECT"/ "AD CON" :
Bluetooth Audio connection status.
"BAT" : Battery level of cell-phone.
"SGNL" : Signal strength of cell-phone.
• "ANS"/ "Auto Answer" (Setting the Time Interval
for Automatic Answer)
This function automatically answers (responds
to) a call after lapse of the preset time interval for
automatic answer.
"OFF" : Does not answer the phone call
automatically.
"0" : Automatically answers the phone call at once.
"1" – "99" : Automatically answers the phone call
after lapse of 1 – 99 seconds.
☞ If the time set in the cell-phone is shorter than that set
in the unit, the former will be used.
• "SPK"/ "SP Select" (Setting up the Voice Output
Speakers)
You can specify the voice output speakers.
"Front"/ "FRT" : Outputs voice from the front-left
and front-right speakers.
"F-R" : Outputs voice from the front-right speaker.
"F-L" : Outputs voice from the front-left speaker.
☞ Select the speaker which is further from the
microphone in order to prevent howling or echoes.
• "C-BP"/ "Call Beep"/ "Beep" (Setting the Beep of
the Incoming Call)
You can output a beep from the speaker when a
call comes in.
"ON" : Beep is heard.
"OFF" : Beep is canceled.
Function Note
• Dial a number
• Depending on the type of your control unit, "|" (all
segments are lit) is displayed for #.
• Calling a number in the call log
• The outgoing call list and the incoming call list, and the
missed call list are the lists of calls originated from and
received at this unit. They are not the ones stored in the
cell-phone memory.
• Calling a number in the Phone Book
• To use the Phone Book, it must have been downloaded
from the cell-phone. For details, see <Downloading the
Phone Book>.
• Up to 19 characters can be displayed for each name in
the Phone Book.
• During search, a non-accent character such as "u" is
searched for instead of an accent character such as "ü".
The non-alphabetical caracters such as Chinese and
Russian are classified as symbol.
• Switching to the Private Mode
• Depending on the type of your cell-phone, switching
to the private talk mode may select the source that was
used before commencing the hands-free connection.
If this happens, the source cannot be switched back to
the hands-free talk mode by operating this unit. Operate