Filter
Top Products
S
S
p
p
e
e
c
c
i
i
f
f
i
i
c
c
a
a
t
t
i
i
o
o
n
n
s
s
a
a
n
n
d
d
I
I
n
n
s
s
t
t
a
a
l
l
l
l
a
a
t
t
i
i
o
o
n
n
Viking offers three variations of hot-line phones and one network dialer. Below are model numbers and descriptions of the Hot
Line phones Viking offers. Each model is designed for specific applications, including varying mounting capabilities and levels of
vandal protection. The following sections describe the product model numbers, their applications, installation and specifications.
Important: Use a minimum wire gauge of 26 when connecting the K-1900 phone to the public switched network.
K
K
-
-
1
1
9
9
0
0
0
0
D
D
-
-
2
2
H
H
o
o
t
t
L
L
i
i
n
n
e
e
D
D
e
e
s
s
k
k
P
P
h
h
o
o
n
n
e
e
To install the K-1900D-2 insert the RJ11 plug into a standard RJ11 jack
as shown to the right.
Dimensions: 230mm x 210mm x 120mm (9.0” x 8.25” x 4.75”)
Shipping Weight: 1.36 Kg (3 lbs)
Connections: RJ11
Colors: Red or Ash
K
K
-
-
1
1
9
9
0
0
0
0
W
W
-
-
2
2
H
H
o
o
t
t
L
L
i
i
n
n
e
e
W
W
a
a
l
l
l
l
P
P
h
h
o
o
n
n
e
e
To install the K-1900W-2 line up the pins of the RJ11W jack with the slots
on the back of the phone, insert and press down as shown to the right.
Dimensions: 102mm x 108mm x 222mm (4.0” x 4.25” x 8.75”)
Shipping Weight: 1.36 Kg (3 lbs)
Connections: RJ11W
Colors: Red or Ash
Optional VE-9x12 Weatherproof Housing for the K-1900W-2, available
in emergency red or safety yellow. For more information on the VE-
9x12, retrieve Fax Back Document 413.
K
K
-
-
1
1
9
9
0
0
0
0
-
-
6
6
H
H
o
o
t
t
L
L
i
i
n
n
e
e
D
D
i
i
a
a
l
l
e
e
r
r
N
N
e
e
t
t
w
w
o
o
r
r
k
k
The K-1900-6 Hot-Line Dialer Network can be
used with any carbon microphone handset and a
double pole hook switch or typical 500, 554, 2500
and 2554 phones. Attach wires as shown to the
right. An electronic ringer may be used if inbound
call capability is required.
Required Handset Type: Carbon microphone
Required Hookswitch: One normally open con-
tact and one normally closed contact
Dimensions: 88.9mm x 68.6mm x 33mm (3.5” x
2.7” x 1.3”)
Shipping Weight: 0.45 Kg (1.0 lb)
Connections: Miniature spade receptacles
Compatible Phones: 500, 554, 2500 and 2554
K
K
-
-
1
1
9
9
0
0
0
0
-
-
7
7
H
H
o
o
t
t
L
L
i
i
n
n
e
e
P
P
a
a
n
n
e
e
l
l
P
P
h
h
o
o
n
n
e
e
To install the K-1900-7 vandal resistant hot line
panel phone, attach the panel to an existing dou-
ble gang box (with minimum dimensions shown
right) using the provided screws. Insert a cord
into the RJ11 jack on the back of the K-1900-7.
Note: Four extra screws and nuts are provided
to fill the unused mounting holes.
Dimensions: 127mm x 254mm x 102mm (5” x
10” x 4”)
Shipping Weight: 1.36 Kg (3 lbs)
Connections: RJ-11
Panel Material: .125 inch stainless steel
Mounting: Flush mount to the included double
gang box. Optional VE-5x10 weather resistant
surface mount box and VE-9x20 weatherproof
box for outdoor applications available.
T
R
S1
S2
RX2
RX1
TX1
TX2
Green
Red
Slate/White
Slate/Green
Slate/Red
Slate/Black
White
Black
Red
White
or
Green
N.O.
N.C.
0.47 mF @ 250V
Capacitor
(included)
Optional Ringer
(not included)
C.O. Line
or Analog
PABX/KSU
Extension
Carbon Mic
Handset
(not
included)
2.75"
2.1"
3.5"
- or -
10.14"
3.69"
5.22"
T
E
L
E
P
H
O
N
E
9.25"
20.25"
- or -
Side View of
the K-1900-7
Double Gang
Electrical Box
(not included)
Hookswitch
(shown on
hook)
RJ11
(not included)
RJ11W
(not included)
T
E
L
E
P
H
O
N
E
Optional VE-9x12
Fax Back Doc 413
(not included)
C.O. Line or Analog
PABX/KSU Extension
K-1900D-2
C.O. Line or Analog
PABX/KSU Extension
K-1900W-2
K-1900-6 PCB with Standard Network
Mounting Bracket (included)
#6-32 x 3/4”
Stainless Steel
Hexdrive Screws
Included
C.O. Line or
Analog PABX/KSU
Extension
Note: If the phone has a ringer,
the included capacitor MUST be installed as shown above.
Optional VE-5x10
Surface Mount Box
Fax Back Doc 424
(not included)
Optional VE-9x20
Weatherproof Box
Fax Back Doc 413
(not included)
-or-
!