Filter
Top Products
Sheet 6
4-2. Switching a Call to the Handset Speakerphone
To switch a normal call to the speakerphone, press [ ] on the handset. To switch back to a normal call, press
[ ] again.
4-3. Transferring a Call
You can transfer a call from one handset to another.
Note: Only one handset at a time can talk with an outside caller. While one handset is in use, other handsets
cannot listen to conversations or make an outgoing call.
During a call, press [delete/transfer]. This places the call on hold.
Press the number key that matches the handset you want to page (1 for Handset 1, 2 for Handset 2, etc.) or
press 0 to page all other handsets. (If you only have two handsets, the phone automatically pages the second
handset for you.)
The handset display shows LINE ON HOLD along with the number of the
handset you are paging. Both your handset and the paged handset sound
a paging tone that is distinct from any of the available ringer tones.
If the other handset picks up the call, the paging tone stops, and your
handset returns to standby.
To cancel the transfer and return to the caller, press [delete/transfer], [TALK/ash] or [ ].
If no one picks up the transferred call within ve minutes, the call will be disconnected.
To receive a transfer call
When a handset receives a transfer page, it sounds the distinct paging tone and shows CALL TRANSFERRED in
the display. To answer a transferred call, pick up the handset and press [TALK/ash] or [ ]. (If Auto Talk
is on, the phone automatically answers when you pick it up from the cradle; if the handset is already o the
cradle, you can also press any key on the twelve-key dial pad.)
1)
2)
3)
4)
•
•
Line on Hold
Transfer to HS1
Line on Hold
Transfer to HS1
4-4. Redialing the Last Dialed Number
Pick up the handset from the cradle.
Press [redial/pause].
Press [TALK/ash] or [ ].
1)
2)
3)
Pick up the handset from the cradle.
Press [TALK/ash] or [ ].
Listen for the dial tone.
Press [redial/pause].
1)
2)
3)
4)
OR
4-5. Adjusting the Speaker Volume
You can change the speaker volume on the handset earpiece, or the handset speakerphone.
When you are on a normal call, press [ ] to make the earpiece louder or [ ] to make it softer.
The handset display shows the current volume level for the earpiece.
When you are using the speakerphone, use [ ] or [ ] to change the speaker volume. The handset display
shows the current volume level for the handset speakerphone.
There are four volume levels: LOW, MEDIUM, HIGH, and MAXIMUM.
Notes:
The handset earpiece and the handset speakerphone have separate volume settings.
If you hear three quick error beeps, it means the earpiece or speaker is already at the lowest (LOW) or highest
(MAXIMUM) volume level.
4-6. Finding a Lost Handset
To locate a lost handset, press [nd hs] on the base. All registered handsets will beep for sixty seconds.
To cancel paging, press [nd hs] again or press any key on the found handset.
4-7. Muting the Ringer
When the phone is ringing, you can mute the ringer on the handset. Muting stops the ringer for the current call
only: the ringer will sound with the next incoming call. You can only mute the handset ringer if the handset is
already o the cradle when the handset starts ringing. Press [END] to mute the incoming ring.
4-8. Voice Mail Waiting IndicatorVoice Mail Waiting Indicator
If you subscribe to voice mail service through your local telephone company, you can use your cordless
telephone to access your voice mailbox. The voice mail company will provide you with the access number.
The /in use LED on the base of your phone ashes whenever you have messages waiting in your voice mailbox.
To access your voice mailbox
Just dial the access number supplied by your voice mail provider to enter your mailbox. You can program your
voice mail access number to a speed dial number.
If the voice mail waiting indicator remains on after you have retrieved your messages, press and hold [nd hs]
for ve seconds. This will reset the indicator.
4-9. Using an Optional Headset
To install a headset, remove the headset jack cover and insert the headset plug
into the headset jack.
When you connect a headset, the earpiece and speakerphone are automatically
muted. If you want to re-activate the earpiece or speakerphone, remove the
headset plug.
You will still make and receive calls as usual: just use your headset to talk to the
caller once the call connects.
You can purchase headsets from our website at www.uniden.com or by calling our Parts Department (See the
back cover page).
•
•
•
•
•
•
5) Using Caller ID and Call Waiting
If you subscribe to Caller ID from your phone company, your phone will show you the caller's phone number and
name (if available) whenever a call comes in. If you subscribe to both Call Waiting and Caller ID, the phone also
shows you the name and the number of any call that comes in while you're on the line.
5/11 12:30PM
Jane Smith
214-555-1234
The date and time received
Caller's name
Caller's Phone Number
Note: If you answer a call before the Caller ID record is received (for example, before the second ring), the Caller
ID record will not appear.
The phone stores the Caller ID information for up to thirty incoming calls - even unanswered calls. If the phone
receives more Caller ID records than it can store, the oldest record in the list is automatically deleted.
For information on storing Caller ID records in the phonebook, see section 6-6.
5-1. Reviewing the Caller ID Record List
You can review the Caller ID list when the handset is in standby or during a call.
Press [cid/menu]. The summary screen displays the total number of CID
records along with the number of new CID records (that is, calls that you
haven't reviewed yet).
Use [ ] to scroll through the records from the latest to the earliest, or
use [ ] to scroll through the records from the earliest to the latest.
Press [cid/menu] to exit the Caller ID list.
1)
2)
3)
Caller ID
New :01
Total:17
Caller ID
New :01
Total:17