Filter
Top Products
Sheet 7
Chain Dialing
The speed dial memory is not limited to phone numbers. You can store
any number (up to twenty digits) that you need to enter once your call
connects. This is referred to as Chain Dialing. An example is a frequently
relled prescription number. Store your pharmacy phone number in
one speed dial and your most frequently relled prescription number as
another speed dial. To use, once connect to your pharmacy's automated
prescription line, simply press [memory] and the speed dial number
where you stored your prescription number and press [select/channel].
6) Using Your Phone
Making and Receiving Calls
Handset on the cradle Handset off the cradle
Making
a call
Pick up the handset from
the cradle.
Press [talk/ash].
Listen for the dial tone.
Dial the number.
OR
Pick up the handset from
the cradle.
Dial the number. Then
press [talk/ash].
1)
2)
3)
4)
1)
2)
Press [talk/ash].
Listen for the dial tone.
Dial the number.
OR
Dial the number. Then
press [talk/ash].
1)
2)
3)
1)
Receiving
a call
Pick up the handset from
the cradle. (If AutoTalk
is on, the phone will
answer the call when
you pick it up.)
Press [talk/ash].
1)
2)
Press [talk/ash] (or
[ /tone/ ], [#/ ] or any
number key if AutoTalk is
on).
Hanging up Press [end] or return the handset to the cradle.
Making a Call from Speed Dial Memory
With the phone in standby, press [memory] to open the speed dial list.
Enter the number ([0] – [9]), or press [vol/ / ] or [vol/ / ] to select
the speed dial number you would like to dial.
Press [talk/ash] to dial the number.
Note: You can also press [talk/ash] before you access the
speed dial memory. When you come to the phone number you
want to dial, press [select/channel].
To cancel speed dialing
Press [end] to return to standby. If accessing the list during an active call,
you can press [memory] to exit the list immediately. If no key is pressed
for thirty seconds, the handset will exit the speed dial list automatically.
Note: Pressing [end] to exit the speed dial list during a call will
disconnect the call immediately.
Transferring a Call
You can transfer a call from one handset to another. Only one handset at a
time can talk with an outside caller. While one handset is in use, the other
handset cannot go off hook to listen to conversations or make an outgoing
call.
During a call, press [delete/transfer]. The call will automatically be
placed on hold and the transfer tone sounds.
To cancel the transfer and return to the caller, press [delete/transfer]
or [talk/ash] on the handset.
When the other handset receives the call, the transfer tone stops.
To receive a transfer call
Do one of the following operation.
Pick up the handset and press [talk/ash].
Pick up the handset from the cradle (when AutoTalk is set to on).
Press any number key, [ /tone/ ] or [#/ ] (when AutoTalk is set to on).
Note: If you transfer a call and it is not picked up after ve
minutes, the call will be disconnected.
Redialing the Last Dialed Number
Pick up the handset from the
cradle.
Press [talk/ash].
Listen for the dial tone.
Press [redial/pause].
1)
2)
3)
4)
OR
Pick up the handset from the
cradle.
Press [redial/pause].
Press [talk/ash].
1)
2)
3)
Adjusting the Handset Earpiece Volume
To change the earpiece volume, press [vol/ / ] or [vol/ / ] during a call.
Adjusting the Ringer Tone and Volume
Changing the Handset Ringer
Your phone has ve different ringer tone/volume combinations you can
choose from. With the phone in standby, press [vol/ / ] or [vol/ / ].
To turn the ringer off, select RINGER OFF.
Muting the Handset Ringer
If the handset is off the cradle while an incoming call is ringing, simply press
[end] to mute the incoming ring. The ringer will sound with the next incoming
call.
Note: You can only mute the handset ringer if the handset is off
the cradle when the phone starts ringing.
1)
2)
3)
1)
2)
•
•
•