Filter
Top Products
Sheet 6
5) Using the Speed Dial Memory
You can store up to ten names and numbers in each handset. You can
dial these numbers with just a few key presses.
Note: When editing the speed dial memory, you must press a key
within thirty seconds or the phone will return to standby.
Storing a Name and Number in Memory
With the phone in standby,
press [memory].
Enter [0] - [9] or use [vol/ / ] and
[vol/ / ] to select the speed dial
location where you would like to store.
Press [select/channel] twice. STORE
NAME appears and a cursor ashes
indicating that the phone is ready for the
name to be entered.
Note: If the selected speed dial
number is already assigned, the Edit
screen appears. You can select EDIT
MEMORY to edit this entry, select
DELETE MEMORY to erase this entry,
or select GO BACK to choose another
speed dial number.
Enter a name (up to thirteen characters) using the keypad. If no name
is required, go to step 5.
Use [ /tone/ ] and [#/ ] to move the cursor to the desired location.
Press [delete/transfer] to delete characters as needed.
If you make a mistake, move the cursor to the incorrect character
and erase the wrong character. Then enter the correct character.
To delete all characters, press and hold [delete/transfer].
If the next character uses the same number key, press [#/ ] rst to
move the cursor over. Otherwise the next time you press the number
key, it changes the character that was previously set.
Refer to the letters on the number keys to select the desired
characters. With each press of a number key, the displayed character
appears in the order shown the following table.
For example, to enter Movies.
1. Press
[6] once.
Then press
[#/ ] to move the cursor to the right.
2. Press
[6] six times.
3. Press
[8] six times.
4. Press
[4] six times.
5. Press
[3] ve times.
6. Press
[7] eight times.
Press [select/channel]. STORE NUMBER is displayed. The cursor
ashes indicating that the phone is ready for the number to be entered.
Use the keypad to enter the phone number (up to twenty digits).
To enter a two-second pause, press [redial/pause].
You can also enter multiple pauses. Each pause counts as a digit.
The display shows a P for every pause.
Press [memory]. Memory storage is
complete.
After about two seconds, the screen
displays the memory list.
Press [end] to exit the memory list. The phone returns to standby.
Storing Caller ID Numbers in Speed Dial Memory
Caller ID names and numbers shown in the Caller ID list can be stored in
speed dial memory.
With the phone in standby, press [cid/menu].
Use [vol/ / ] or [vol/ / ] to select the phone number you would like
to store.
Press [memory].
Enter a number ([0] – [9]) or press [vol/ / ] or [vol/ / ] to select the
memory location to be stored.
Press [select/channel] to store the number.
Note: If a number has already been
stored in the selected memory location,
a conrmation screen is displayed. To
overwrite, press [vol/ / ] to select YES
and press [select/channel].
The display returns to the Caller ID list.
1)
2)
3)
4)
•
•
•
•
•
5)
6)
•
•
7)
8)
9)
1)
2)
3)
4)
5)
6)
Select Memory
01ｰ
02 JOHN DOE
Select Memory
01ｰ
02 JOHN DOE
Store Name Store Name
ｰEdit Memory01
Delete Memory01
Go Back
ｰEdit Memory01
Delete Memory01
Go Back
keys 1 2 3 4 5 6 7 8 9
1
A B C a b c 2
D E F d e f 3
G H I g h i 4
J K L j k l 5
M N O m n o 6
P Q R S p q r s 7
T U V t u v 8
W X Y Z w x y z 9
* # - & ( )
(blank)
0
Number of times key is pressed
keys 1 2 3 4 5 6 7 8 9
1
A B C a b c 2
D E F d e f 3
G H I g h i 4
J K L j k l 5
M N O m n o 6
P Q R S p q r s 7
T U V t u v 8
W X Y Z w x y z 9
* # - & ( )
(blank)
0
Number of times key is pressed
Memory01 StoredMemory01 Stored
Replace Memory?
Yes
ｰNo
Replace Memory?
Yes
ｰNo