Filter
Top Products
ANSWERING THE DOOR PHONE
When your station is programmed to receive calls from the door phone:
• You will receive three short rings repeatedly.
• Lift the handset and you will be connected to the door phone.
• If an electric door lock release is installed, hookflash, receive confir-
mation tone and dial 13 to release the lock.
CALLING THE DOOR PHONE
(ROOM MONITORING)
You can call the door phone and listen to what is happening outside or in
another room.
• Lift the handset and then dial the extension number of the door box.
• You will be connected to the door phone. You can listen or have a
conversation.
• If an electric door lock release is installed, hookflash, receive confir-
mation tone and dial 13 to release the lock.
APPOINTMENT REMINDER /
ALARM CLOCK
This feature works like an alarm clock. Use it to remind yourself of an
appointment later in the day (TODAY ONLY) or as a daily reminder every day
(DAILY). You can set up to three alarms. Each one can be either a TODAY
ONLY or a DAILY alarm.
When the alarm rings, you will hear three short rings repeated three times.
Lift the handset to answer the alarm. If you do not, the alarm will alert you
two more times at pre-determined time intervals.
To set/reset alarms:
• Go off-hook. Dial 15 and then 112.
• Dial the alarm number 1, 2 or 3.
• Dial the time you want the alarm to sound. Enter the time as HHMM
(hours & minutes) using a 24 hour clock.
• You receive confirmation tone after dial 0 (NOT SET), 1 (TODAY
ONLY) or 2 (DAILY) to select alarm type.
• Receive confirmation tone and go on-hook.
• Repeat for each alarm if needed. (Receive confirmation tone)
Note: If you are presented with an error tone at any time, then go on-hook
and resume from the beginning.
19
iDCS_16_SLT.qxd 12/14/2004 4:01 PM Page 23
ACCOUNT CODES
When it is equipped with optional equipment, your SAMSUNG iDCS 16 sys-
tem allows calls to be charged to different accounts. You can enter an ac-
count code in two ways. To enter an account code by interrupting the con-
versation:
• While on an outside call, hookflash, receive confirmation tone and
dial 47.
• Dial the account code (it may be a maximum of 12 characters includ-
ing 4 and #).
• Hookflash to return to the conversation.
• If you make an error, repeat the procedure with the correct code. Only
the last account code dialed will be recorded.
To enter an account code after the outside party hangs up.
• After the outside party hangs up, hookflash, receive confirmation tone
and then dial 47.
• Dial the account code (it may be a maximum of 12 characters includ-
ing 4 and #).
NOTE: If you wait for the outside party to hang up, you must complete this
procedure within ten seconds. You cannot repeat if you make a mistake.
IN/OUT OF GROUP
If your station is assigned to a hunt group, this feature will allow you to dial
an access code plus the group number, e.g., 501, plus 0 to temporarily pre-
vent your station from receiving any group calls. You will still be able to
receive calls that are dialed directly to your station. To reenter the group, dial
an access code plus the group number, e.g., 501, plus 1.
DIAL BY VOICE
If your station is assigned to a Dial by Voice group, this feature allows you
to use Dial by Voice. Before using this feature, you must record a name and
assign that name to a personal speed bin. This feature can be accessed
only by a dial code. When you are recording a name, do not pause between
the first and last names because the system will interpret the pause as the
end of the recording. Practice saying names as one word, e.g. Saint cho,
Robert Kim, Candy Kim.
IMPORTANT: To record a name for one of your speed dial numbers the fol-
lowing procedure must be followed in one complete step. Stopping causes
recording to fail.
20
iDCS_16_SLT.qxd 12/14/2004 4:01 PM Page 24