Filter
Top Products
MANUAL SIGNALLING
Use this feature when you want to send a brief 500ms ring burst to another sta-
tion,regardless of the status of your phone (on-hook,off-hook,handsfree,DND, or
ringing).
To send a signal to another station:
• Press the Manual Signalling (MS) key.
• You may press the MS key repeatedly to send multiple signals to the desig-
nated station.
NOTE: Your phone must have a Manual Signalling (MS) key with a station
number extender assigned to it.
OFF-HOOK VOICE ANNOUNCE
Keysets may receive a voice announcement while on another call.The calling sta-
tion must have an OHVAkey.When you are in DND,you cannot receive OHVA calls.
The OHVA feature will work with intercom and transferred calls.
When you receive an OHVA and secure OHVA is ON, you will hear the announce-
ment in the handset receiver, if you are using the handset. If secure OHVA is OFF
then you will hear the announcement on the speaker, if you are talking on the
handset. If you are using the speakerphone the announcement will always be
heard through the speaker.
To make an off-hook voice announcement:
• Dial the extension number or press the DSS key.
• When you receive a busy signal,press the OHVA key.
• After the attention tone,begin speaking.
• Finish the call by replacing the handset or pressing the ANS/RLS key.
• Press the flashing CALL button on your keyset. This will place the original
party on hold and allow you to talk to the announcing party.
• To return to your first party,press the key corresponding to your original call.
This will disconnect the OHVA call.
NOTES:
1. When you are voice announcing to a station close to you, use the handset to
avoid an echo effect.
2. You cannot off-hook voice announce to single line telephones.
If your keyset is associated with a DCS 32 Button Add-On Module,you can receive
Executive OHVA calls.Executive Off-Hook Voice Announce allows you to engage in
conversation on your keyset and simultaneously receive and reply handsfree to an
OHVA through your DCS 32 Button Add-On Module (AOM). Use caution because
39
idcs_keyset.qxp 9/23/2005 11:32 AM Page 45
the conversation through the AOM may possibly be heard by the caller on the
keyset.When you receive an executive OHVA through your AOM:
• Reply by speaking in the direction of the microphone in the AOM unit.
• Adjust the volume with the VOLUME keys on the AOM unit.
• Press the SPK key on the AOM to disconnect the announcing party.
NOTES:
1. Executive off-hook voice announce can only be accomplished when an AOM
is attached to your phone.
2. If the MUTE key on the AOM is lit, you must press the AOM’s SPK key to
answer the OHVA call.
OHVA BLOCK
Your keyset can be programmed with an OHVA Block (BLOCK) key. Pressing this
key will prevent anyone from making an OHVA to you until you press the button
again and cancel the blocking.
OHVA REJECT
Your keyset can be programmed with an OHVA Reject (REJECT) key.Pressing this
key while receiving an OHVA call will disconnect the voice announcing party and
return you to your original call.
IN GROUP/OUT OF GROUP
If your keyset is assigned to a station ring group,you can remove your keyset from
the group and then put it back in.While you are out of the group,you can receive
calls to your extension number but not calls to the group number.If you have an
IN/OUT key with the group number assigned.
• Press the IN/OUT key.It will light red when your keyset is in the group.
• Press the IN/OUT key again to exit the group and turn the light off.Repeat as
necessary.
If you do not have an IN/OUT key:
• Dial the IN/OUT access code number ________________, then the group
number, then 0 to exit the group or 1 to enter the group.
NOTE: If the Hot Keypad feature has been turned off, you must first lift the hand-
set or press SPEAKER key.
The IN/OUT key can include an extender to indicate the specific group that this
key will affect. This means that if you are in multiple groups, you can decide for
which groups you will receive calls.
40
idcs_keyset.qxp 9/23/2005 11:32 AM Page 46