Filter
Top Products
9
Preparation
2. Press
;
;;
;
to darken the display, or
:
::
:
to lighten the
display.
Note:
The phone sounds 3 beeps when you reach
the lowest or highest contrast level.
3. Press
FUNCTION
to save the new setting and enter
the area code setting mode.
7H;7
7H;77H;7
7H;7
9E:;
9E:;9E:;
9E:;
3
33
3
###
######
###
appears.
Note:
In Steps 2 and 3, if you do not press a key within
12 seconds, the corded phone exits the display contrast
setup.
STORING YOUR AREA CODE
To dial a number from a Caller ID or VIP record (see
“Dialing a Number From a VIP or Caller ID Record” on
Page 17), you must first store your local area code in the
phone’s memory. Then, when you dial from a Caller ID or
VIP record, the system skips the area code if it matches
the one you stored.
Note:
Do not store the area code if your area requires ten
digit dialing. Otherwise, it dials incorrectly on call back.
Corded Phone
When
7H;7
7H;77H;7
7H;7
9E:;
9E:;9E:;
9E:;
3
33
3
###
######
###
appears, enter your three-digit
area code within 12 seconds. The phone beeps twice.
The area code is stored and the phone returns to standby
mode. To replace a stored area code, store a new one in
its place.
Note:
If you are not in the Area Code setting mode, hold
down
FUNCTION
for 2 seconds, then press
FUNCTION
again to skip the display contrast mode.
7H;7
7H;77H;7
7H;7
9E:;
9E:;9E:;
9E:;
3
33
3
###
######
###
appears.
Cordless Handset
Press and hold
#/FUNC
on the cordless handset until
7H;7
7H;77H;7
7H;7
9E:;
9E:;9E:;
9E:;
3
33
3
###
######
###
appears. Enter your three-digit area code
within 12 seconds. The cordless handset beeps twice.
The area code is stored and the cordless handset returns
to standby mode. To replace a stored area code, store a
new one in its place.
USING THE DATA PORT
The corded phone is equipped with an extra phone jack
that allows you to connect to a computer modem. You
need a modular cord (available at your local RadioShack
store) to connect the phone to a computer modem.
Plug one end of the modular cord into the
DATA PORT
jack on the back of the corded phone. Plug the modular
cord’s other end into a computer modem’s telephone line
jack.
Note:
You cannot use the data port and the telephone at
the same time.
SETTING UP THE CORDLESS
HANDSET
Resetting the Security Access-Protection
Code
If the cordless handset does not work immediately after
charging or recharging the battery pack, you must reset
the security access-protection code (see “Connecting,
Charging and Replacing the Cordless Handset’s Battery
Pack” on Page 7).
1. Hold down
DELETE
on the corded phone for until
>I
>I>I
>I
H;=?IJH7J?ED
H;=?IJH7J?EDH;=?IJH7J?ED
H;=?IJH7J?ED
appears.
2. Within 12 seconds, hold down
FLASH/DELETE
on the
cordless handset until
ý?D?J?7B?P7J?ED$$
ý?D?J?7B?P7J?ED$$ý?D?J?7B?P7J?ED$$
ý?D?J?7B?P7J?ED$$
appears.
Note:
If you wait longer than 12 seconds, the phone
exits security code setup.
3. Once the cordless handset successfully receives the
security code from the corded phone, the cordless
handset and the corded phone beeps twice.
9ED<?HC;:
9ED<?HC;:9ED<?HC;:
9ED<?HC;:
appears on both phones.
Using a Headset
You can make or answer calls
with hands-free convenience
using an optional headset that
has a
3
/
32
-inch (2.5 mm) plug.
Contact your local RadioShack
store for a suitable headset.
To connect the headset, insert
the headset plug into the
headset jack on the cordless
handset.
DC 12V
300mA Jack
DATA PORT
TEL LINE