Filter
Top Products
12
Operation
MAKING AND ANSWERING A CALL
Corded Phone
To make a call using the corded phone, pick up the
corded handset or press
SPEAKER
to use the
speakerphone. You hear a dial tone and
;DJ;H
;DJ;H;DJ;H
;DJ;H
DKC8;H
DKC8;HDKC8;H
DKC8;H
5
55
5
appears (if you are using speakerphone, the red
SPEAKER indicator also lights). Dial the desired number.
Note:
When you press
∗
∗∗
∗
or
#
##
#
, the corded phone’s
display shows
7
77
7
or
X
XX
X
respectively.
To answer a call, pick up the corded handset or press
SPEAKER
.
To end a call, press
SPEAKER
or return the corded
handset to its cradle.
Note:
Even when there is an AC power failure and no
battery is installed in the corded phone, you can still
make and receive calls using the corded handset. But
you cannot use the cordless handset or the
speakerphone, or other functions of the phone.
Cordless Handset
To make a call using the cordless handset, lift the
cordless handset, then press
TALK
.
M7?J?D=
M7?J?D=M7?J?D=
M7?J?D=
appears.
When the cordless handset links up with the corded
phone, the channel, call duration timer and the receiver
volume level appear. You hear a dial tone. Dial the
desired number.
To answer a call, lift the cordless handset, then press
TALK
.
To end a call, press
TALK
or place the cordless handset
on its cradle.
Notes:
• The call duration timer starts counting from
&&0&&
&&0&&&&0&&
&&0&&
when you dial the number or receive a call, and
stops counting when you hang up the phone. The
call duration appears briefly after you hang up the
phone.
• When you press a button, a single tone indicates
that the phone has accepted the command. Three
tones indicate that you pressed a button in error, or
there is severe interference.
• If interference is severe, the cordless handset might
lose communication with the corded phone and the
call might disconnect. If this happens, reset the
cordless handset’s security access-protection code
(see “Resetting the Security Access-Protection
Code” on Page 9).
ADJUSTING THE VOLUME
Corded Phone
To adjust the corded handset’s volume, pick up the
corded handset, then repeatedly press
VOLUME
8
88
8
or
9
99
9
. The volume level (up to 4 levels) you selected
appears. The volume level remains set after you hang
up.
To adjust the speakerphone’s volume, press
SPEAKER
,
then repeatedly press
VOLUME
8
88
8
or
9
99
9
. The volume
level (up to 8 levels) you selected appears. The volume
level remains set after you press
SPEAKER
again.
Cordless Handset
To adjust the cordless handset’s volume, press
TALK
.
Then repeatedly press
VOL/CID
8
88
8
or
9
99
9
. The volume
level (up to 4 levels) you selected appears. The volume
level remains set after you hang up.
Note:
The corded phone or the cordless handset sounds
3 beeps when you reach the lowest or highest listening
level.
USING TONE SERVICES ON A
PULSE LINE
Some special services, such as bank-by-phone, require
tone signals. If you have pulse service, you can still use
these tone services by following these steps:
1. Dial the service’s main number.
2. When the service answers, press
TONE/
∗
∗∗
∗
/VIP
on the
cordless handset or
TONE/
∗
∗∗
∗
on the corded phone.
Any additional numbers you dial are sent as tone
signals.
3. After you complete the call, hang up the phone. The
phone automatically resets to pulse dialing.
USING PAGE/INTERCOM
Using the corded phone, you can send a page to the
cordless handset to locate it when it is away from the
charging cradle and not in use. You can use the corded
phone’s intercom feature to carry on a conversation with
a person using the handset.
To page the cordless handset,
press
PAGE/INTERCOM
on
the corded phone. The cordless handset beeps for about
15 seconds. Hold down
PAGE/INTERCOM
for about 3
seconds. The cordless handset beeps for about 1
minute.
F7=?D=
F7=?D=F7=?D=
F7=?D=
appears on both the corded phone’s and
the cordless handset’s displays. Press
INTCM
on the
cordless handset to talk with the corded phone. The
channel,
?DJ9C
?DJ9C?DJ9C
?DJ9C
and the volume level appear on both the
corded phone’s and cordless handset’s displays.