Filter
Top Products
12
Installation
If you have trouble replacing the battery
pack, take the phone to your local Ra-
dioShack store for assistance.
Important:
The EPA certified
RBRC
®
Battery Recycling Seal
on the nickel-cadmium (Ni-Cd)
battery indicates RadioShack
is voluntarily participating in an
industry program to collect and recycle these
batteries at the end of their useful life, when
taken out of service in the United States or
Canada. The RBRC program provides a
convenient alternative to placing used Ni-Cd
batteries into the trash or the municipal
waste stream, which may be illegal in your
area. Please call 1-800-THE-SHACK (1-
800-843-7422) for information on Ni-Cd bat-
tery recycling and disposal bans/restrictions
in your area. RadioShack’s involvement in
this program is part of the company’s com-
mitment to preserving our environment and
conserving our natural resources.
SETTING THE DIALING
MODE
Your phone comes set for tone dialing. If you
have pulse service, you need to change the
dialing mode. If you are not sure which type
of service you have, do this test.
Press
SPEAKER
and listen for a dial tone.
Press any number other than
0
.
Note:
If your phone system requires that you
dial an access code (9, for example) before
you dial an outside number, do not press the
access code either.
If the dial tone stops, you have touch-tone
service. If the dial tone continues, you have
pulse service.
To set the dial mode, press
SPEAKER
to
hang up the phone if necessary, then hold
down
FLASH
on the base until the phone
beeps and
ý:_WbýCeZ[0
ý:_WbýCeZ[0ý:_WbýCeZ[0
ý:_WbýCeZ[0
and the current dialing
mode,
Je d[
Je d[Je d[
Je d[
or
Fkbi[
Fkbi[Fkbi[
Fkbi[
, appear. Then press
#
to
set to pulse mode or
*
to set to tone mode.
The phone beeps and displays
Fkbi[ý :_Wb_d]
Fkbi[ý :_Wb_d]Fkbi[ý :_Wb_d]
Fkbi[ý :_Wb_d]
or
Jed[ý:_Wb_d]
Jed[ý:_Wb_d]Jed[ý:_Wb_d]
Jed[ý:_Wb_d]
, then the display clears.
Note:
The phone exits the setting mode if a
call or page is received, or if you press
TALK
on the handset or any key on the base.
SETTING THE RINGER
TONE/VOLUME
You can select one of four different ringer
tone/volume settings on the handset. At any
time, except during a call or while reviewing
Caller ID records, repeatedly press
VOL/CID
8
88
8
or
9
99
9
to select the desired ringer setting.
Each time you press a button, the phone
rings at the selected setting and the display
shows
H_d][h
H_d][hH_d][h
H_d][h
7
77
7
>_]^
>_]^>_]^
>_]^
,
H_d][h
H_d][hH_d][h
H_d][h
7
77
7
Bem
BemBem
Bem
,
H_d][h
H_d][hH_d][h
H_d][h
8
88
8
>_]^
>_]^>_]^
>_]^
, or
H_d][h
H_d][hH_d][ h
H_d][h
8
88
8
Bem
BemBem
Bem
.
You can also turn off the ringer. At any time,
except during a call, press and hold
VOL/CID
9
99
9
until the phone beeps and the display
shows
H_d][h
H_d][hH_d][h
H_d][h
E\\
E\\E\\
E\\
. When you place the hand-
set face up on the base,
2H_d][hý E\\4
2H_d][hý E\\42H_d][hý E\\4
2H_d][hý E\\4
ap-
pears.
You can still make or receive a call even
when the ringer is set to off. When you have
an incoming call, the phone connected to the
same line rings, and
?dYec_d]
?dYec_d]?dYec_d]
?dYec_d]
9Wbb
9Wbb9Wbb
9Wbb
appears.
To turn the ringer back on, simply press
VOL/
CID
8
88
8
or
9
99
9
; the ringer is set to
H_d][h
H_d][hH_d][h
H_d][h
7
77
7
>_]^
>_]^>_]^
>_]^
.
To set the base’s ringer volume, at any time
except during a call, repeatedly press
RING
on the base until you get the desired setting
–
H_d][hý >_]^
H_d][hý >_]^H_d][hý >_]^
H_d][hý >_]^
,
H_d][h
H_d][hH_d][h
H_d][h
Bem
BemBem
Bem
, or
H_d][h
H_d][hH_d][h
H_d][h
E\\
E\\E\\
E\\
ap-
pears. When you turn off the ringer.
2H_d][h
2H_d][h2H_d][h
2H_d][h
E\\4
E\\4E\\4
E\\4
remains on the display.
Note:
When you set the base’s ringer off, the
base (and the handset if it is on the base)
does not ring but another phone connected
to the same line rings and
?dYec_d]ý9Wbb
?dYec_d]ý9Wbb?dYec_d]ý9Wbb
?dYec_d]ý9Wbb
ap-
pears. If the handset is away from the base,