Filter
Top Products
I
REMOTE
OPERATION
Playing
Messages
SCO
1
Dial
your
telephone number
from
a touch
tone phone.
2
When
the
system answers, enter
your
Remote Access Code.
The
system
announces
the
number
of
messages
received,
then
beeps
twice.
3
After
the two
beeps,
wait
4
seconds, and
the system plays back
messages
— OR
—
Press
and
release
Q]
to
play
all
messages
— OR
—
Press
and
release
2 to
play
only
new-
messages
(if
there
are no new
messages,
the
system announces "No
new
messages.")
4
To
repeat
a
message
—
Press
and
release
\4_
while
the
message
is
playing.
To
repeat
part
of a
message
—
Hold
down
gj- To resume
playing,
release
H-
To
skip
a
message
—
Press
and
release
while
the
message
is
playing.
H". To resume
playing,
release
6.
To
stop message playback
—
Press
and
release dl.
To
save messages, hang up.
Oeletlng
Messages
To
delete selected message
—
Press
and
release
%
while
the
message
is
playing.
To
delete all messages
—
After
you have
listened
to
all
messages
and
heard
the 2
beeps,
press
g),
[3].
Record
Announcement
1
Press
[2, [*]•
2
Speak after the beep, then
press
(U
to stop
recording.
The system replays
your
new
announcement.
To
review your announcement
—
Press
0,
[7].
Record
a
Memo
1
Press
# and
begin speaking after
the
beep.
2
Press
fs] when you
are
finished.
Room
Monitor
with
Intercom
You
can
call
the answering system and
listen
to
any
activity
in the
room.
1
Press
:9
,
iT
to
listen
for 30 seconds.
2
If
you
wish,
you can
press
[Tj
while
the
monitor
is
active
to
speak
to
some-
one in the
room
(up
to
30 seconds).
3
Press
iagain
during
intercom
operation
to
return
to
listening
only.
4
Press
[5j at any
time
to
exit
Room
Monitor
with
Intercom.
Ending
the
Remote
Access
Call
Press
i¥j, i9].
The
system announces
"The
machine
will
now hang up,"
and
disconnects
from
the
line.
Changing
Remote
Access
Code
1
Press
m,
[9].
The
system announces
"Enter
new code."
2
Enter
your
new Remote Access Code,
^„^y
number between 500 and 999.
^_
3
If a
valid
code
is
entered,
the
system
announces
the new
Remote Access
Code.
If an
invalid
code
is
entered, the
system
beeps
5 times
rapidly,
then
beeps
twice.
Repeat
Steps
1 and
2.
Turn
System
Off
Press
m, [S.
Turn
System
On
When
the system is off, it answers after 10 rings
and
beeps
twice.
1
Press
0 to
turn
the system on.
2
The system
beeps
twice
and
is
ready
to
answer calls and record
messages.
If
the
-t
system
beeps
5 times, the memory is
full.
Memory
FuR
If
the system answers after 10 rings and
beeps
twice
instead of
playing
your
announcement, it
might
be
off or memory
might
be
full.
1 Enter Remote Access Code after
2-beep
signal.
2
Listen
to
messages,
and delete some
or
all
of them.
3
Press
\0]
to
make sure
your
system
is
on
before
you hang up.