Filter
Top Products
OPERATION
Skip
to next message
—
Press
and
release
WIlBII
MCmOIV
IS
FUll
ISKIP/SCANi.
Skip
part of a message —
Hold
down
{SKIP/SCAN':
for a few
seconds,
then
release
it
to
resume
playing.
The system
beeps
while
the button is held
down.
Stop message playback —
Press
and
release
\STOP:.
Saving
Messages
The system
saves
your
messages
automatically
if
you do not delete them. The system can
save
about 12 minutes of
messages,
including
your
announcement, for up to a
total
of 99
messages.
When
memory is
full,
you must delete some or
all
messages
before new
messages
can be re-
corded.
Oeletlng
Messages
Delete all messages —
Hold
down
'DELETE\
The system announces
"Messages
deleted"
and the Message
Window
displays 0. If
you
haven't listened to all of the
messages,
the system
beeps
5 times, and
does
not
delete
messages.
Delete selected messages —
Press
and re-
lease
IDELETE':
while
the
message
you want
to
delete is being played. The system
beeps
once, and continues
with
the next
message.
If
you want to check a
message
before you
delete
it,
you can
press
REPEAT/SCAN]
to replay
a
message
before deleting it.
When
the system
reaches
the end of the
last
message,
the
messages
not deleted are
renumbered, and the Message
Window
displays
the
total
number of
messages
remaining
in memory.
Recording
a
Memo
You
can record a memo to be stored as an
incoming
message.
The memo can be up to 3
minutes
long,
and
will
be played back
with
other
messages.
1
Press
and
release
[MEMO].
After
the beep,
speak
toward the microphone.
2
To stop recording,
press
[sToPi.
The system can record approximately 12
minutes of
messages,
including
your
announcement, for up to a
total
of 99
messages.
When memory is
full,
or 99
messages
have been recorded, the Message
Window
flashes F. Delete
messages
to make
room
for new
ones.
When
memory is
full,
the system answers calls
after
10 rings, and
sounds
2
beeps
instead of
your
announcement.
Remote
Access
Code
You
can use many features of this answering
system remotely
from
a touch tone phone.
Most
features can be
accessed
only
after
yjou,^^
enter a Remote Access Code, preset td'500^
You
can
view
the Remote Access Code by
tapping
{CODE].
You
can change the Remote Access Code to
any
3^digit
number
from
500-999.
1
Press
and
release
.CHANGE]
.
The Message
Window
displays
CH.
2
Press
and
release
ICODEI.
The system
announces
"First
digit."
3
Press
MP/SCAN]
or
JWEAT/SCAN]
to change the
digit.
4 When the Message
Window
displays the
desired
first
digit,
press
and
release
WDEJ-
The system announces "Second
digit."
5
Press
]SKIP/SCAN\r
lflfP£4r/Sc;i«i
to change the
digit.
6 When the Message
Window
displays the
desired second
digit,
press
and
release
[COPIj.
The system announces
"Third
digit."
7
Press
]SKIP/SCAN\r
]REPEAT/SCAN]
to change the
digit.
8 When the Message
Window
displays the
desired
third
digit,
press
and
release
{CODE'..
The system announces the new
Remote Access Code.