Filter
Top Products
10
Wireless Transmitter Programming
Up to 500 wireless transmitters can be used with the system. Transmitters can
be ordered in pre-programmed blocks of sequential ID codes. Up to 16 blocks of
transmitters can be used. Transmitter blocks can be ordered with a Facility Code
of 1-15 for block identifi cation if desired. Using Facility Codes is optional. For
security, an individual transmitter can be deactivated in case it is lost or stolen.
✦ NOTE: Transmitters will activate Relay Channels “A” or “B” depending
on the setting of the transmitter button options. See the table below for
the factory preset button options. Your installer may have modifi ed these
options. Check boxes are provided to log any modifi ed button options.
TRANSMITTER BUTTON OPTIONS
SINGLE BUTTON,
LEFT BUTTON,
OR TOP LEFT BUTTON
RIGHT BUTTON
OR TOP RIGHT BUTTON
TOP BUTTON
(AVAILABLE ON SOME
MODELS ONLY)
BOTTOM LEFT BUTTON
BOTTOM RIGHT
BUTTON
TYPE OF
TRANSMITTER
❑ NO RELAY
❑ RELAY “A” (PRESET)
❑ RELAY “B”
❑ RELAYS “A” & “B”
N/A N/A N/A N/A
SINGLE BUTTON
❑ NO RELAY
❑ RELAY “A”
❑ RELAY “B” (PRESET)
❑ RELAYS “A” & “B”
❑ NO RELAY (PRESET)
❑ RELAY “A”
❑ RELAY “B”
❑ RELAYS “A” & “B”
N/A N/A
TWO BUTTON
❑ NO RELAY (PRESET)
❑ RELAY “A”
❑ RELAY “B”
❑ RELAYS “A” & “B”
❑ NO RELAY (PRESET)
❑ RELAY “A”
❑ RELAY “B”
❑ RELAYS “A” & “B”
FOUR BUTTON
Assign Block Transmitter
Assigning a transmitter block assigns memory space for each block of transmitters
used with the AE-500.
✦ NOTE: When a block of transmitters is assigned, all transmitters in the
block will become active and ready to use.
1. If not already in Programming Mode, connect by telephone or use the
local keypad. Enter the master password and access programming.
2. Press
3. Enter the number of transmitters in the block.
4. Press
5. Enter the transmitter block’s facility code.
✦ NOTE: Facility codes are optional. Enter 0 to have the system ignore the
transmitter block’s facility code.
6. Press
7. Enter the fi rst (lowest) transmitter ID number for the block of transmitters.
8. Press
9. Exit Programming Mode if all programming is complete.
Assign Single Enrolled Transmitter
Assigning a transmitter allocates memory space for the transmitter
✦ NOTE: When a transmitter is assigned, it will become active and ready to
use.
1. If not already in Programming Mode, connect by telephone or use the local
keypad. Enter the master password and access programming.
2. Press
3. Enter the transmitter facility code (enter 0 if not used).
4. Press
5. Enter the transmitter ID number of the transmitter.
6. Press
7. Exit Programming Mode if all programming is complete.
Suspend a Transmitter
Transmitters may be suspended if necessary (such as when a transmitter is lost
or stolen).
1. If not already in Programming Mode, connect by telephone or use the
local keypad. Enter the master password and access programming.
2. Press
3. Enter the transmitter’s facility code (enter 0 if not used).
4. Press
5. Enter the transmitter’s ID number.
6. Press
7. Exit Programming Mode if all programming is complete.
PPN 41
41#NUMBER#FC#ID#
NUMBER = NUMBER OF TRANSMITTERS IN THE BLOCK
FC = FACILITY CODE 0-15 (0 IF UNUSED)
ID = LOWEST TRANSMITTER ID NUMBER IN THE BLOCK
ASSIGN BLOCK TRANSMITTER
PPN 43
43#FC#ID#
FC = FACILITY CODE 0-15 (0 IF UNUSED)
ID = TRANSMITTER ID NUMBER
SUSPEND A TRANSMITTER
PPN 45
45#FC#ID#
FC = FACILITY CODE (0 IF UNUSED)
ID = TRANSMITTER ID NUMBER
ASSIGN SINGLE ENROLLED TRANSMITTER