Filter
Top Products
4. If someone tries to reach you on the
Intercom while you are talking on the
handset, you will hear three rings.
Press HOLD, then INTCM on the
handset. (The base will beep and
speakerphone will activate.
Speakerphone LED will flash when
there is a call on hold). Your caller will
then be put on hold while you
answer the INTCM. The TALK button
will flash to remind you that you have
a call on hold. Press TALK again to
disconnect the INTCM and
reconnect with your telephone call.
To Use The Intercom
As A Monitor
Monitor the room in which the base is
located from another location using the
Intercom feature.
1. Press INTCM button on the handset.
This engages the itercom
microphone in the base, allowing you
to listen to the base location area.
2. Listen through the handset for as
long as you like.
3. Disconnect by pressing INTCM
again.
4. If you receive an incoming call while
you are using the monitor, you will
hear a ringing in the handset.
5. Press TALK to connect the call. The
Intercom is automatically
disconnected.
Call Dad to dinner, monitor the baby while
you do laundry or keep an ear out to make
sure that the children aren’t hurt. These
options, along with many others, are at your
fingertips with your Cobra Intenna because
it doubles as a two-way intercom/paging
system between the base and the
handset—and outside calls will still come
through! If you should misplace the
handset, simply activate the pager and
follow the signal until you locate it.
To Use The Intercom/Pager
1. If you are at the handset and wish to
speak with someone at the base,
press and release INTCM which will
sound three rings and light the red
indicator next to the INTERCOM
button on the base. The person may
then respond just by speaking into
the base. To end the conversation,
simply press the INTCM button on
the handset again.
2. If you are at the base and wish to
page someone at the handset, press
and release INTERCOM, which will
sound a series of three beeps and
light the INTCM button on the
handset. The person may then
respond by pressing INTCM and
speaking into the handset.
3. If you receive a call during an
intercom conversation, you will hear
a low volume ringing. If you are at
the handset, press TALK, which will
disconnect the intercom and connect
you with the incoming call. If you are
at the base, press SPEAKERPHONE.
To Use The Pager
As A Handset Locator
1. To locate a misplaced handset around
the home, press and release the
INTERCOM button on the base.
2. The handset will sound a series of
three beeps for 30 seconds, giving
you time to locate it. Once found,
press and release the INTCM button
on the handset to eliminate the
signal.
3. If you have not located the handset
in 30 seconds, repeat steps above.
13
1-773-889-3087
NEED HELP?
CP-720
Cobra
®
USING THE BUILT-IN
INTERCOM/PAGING SYSTEM
2
USING THE SPEAKERPHONE
4
Whether you’re conducting a business
meeting or want to let everyone in the
family hear and talk when grandma calls to
say “hello”, nothing beats the convenience
of our new speakerphone.
To Use The Speakerphone
After your call is connected, simply
press the button on the base next to
SPEAKERPHONE and the red LED will
light, indicating that the speakerphone
is on. If desired, one person may
continue to speak through the handset
while connected. Press the button
again to disconnect.
1
2
3
INTERCOM
INTCM
TALK
3
TALK
4
SPEAKER-
PHONE
5
HOLD
3
INTERCOM
1
INTCM
1
INTCM
1
INTCM
1
INTCM
TALK
SPEAKER-
PHONE
1
3
5
4
2