Filter
Top Products
Memory dialing lets you store and dial 32
commonly-called telephone numbers
automatically, just by pressing a button.No
more fumbling with the phone book,
guessing at numbers or accidentally
misdialing the people you call most.
To Store A Number In Memory
Using the Base Keypad:
In order to accomodate 32 numbers, your
memory system is designed with 16
buttons which control both upper (1-16) and
lower (17-32) banks of memory numbers. A
red LED (light-emitting diode) lights to show
you are using either upper or lower bank. To
switch banks, press the button next to the
LED marked “Lower”.
To program numbers
into the memory bank
from the base:
1. Make sure the LED for the bank you
want (“Upper” or “Lower”) is lit. If
not, press the button next to the
“Lower” LED until the correct LED
lights.
2. Press the button for the memory
location you wish to program. You
will hear a beep and the LED will
flash to let you know it is ready to
store a number. You have 10 seconds
to begin programming the number (if
10 seconds elapses without digits
being entered, the LED will stop
flashing, you will hear a long beep
and the LED will light steadily again).
3. Enter the number you wish to store
(up to 16 digits).
4. Press the same memory button
again. You will hear two double
beeps to confirm the number is
stored. If you hear three beeps
instead, you may have pressed the
incorrect storage button, and you’ll
need to repeat the steps above.
5. Repeat the above steps for up to 32
positions. Be sure to note the names
for each number you are storing, so
you can create your directory card
when you are finished.
To Store A Number
Longer Than 16 Digits
For telephone banking or alternate long
distance service, you may need to program
a number that is longer than 16 digits. To do
so, you will need to divide the number
between two different memory locations.
Example: Store an alternate long distance
acces number in location 1 and personal
identification number for that service in
location 2.
Creating A Directory
As you are programming the memory bank,
you will want to keep track of whose
number you are assigning to each location.
When finished, you may indicate who is
assigned to each number by filling in the
directory located on the base. This provides
a quick and easy reference. To create the
directory, remove the protective plastic
cover by sliding it gently toward the middle
and lifting it out. Fill in the names on the
directory next to the number they have
been assigned and replace the cover.
To Dial A Number Stored In
Memory From Base Keypad
Using Speakerphone
1. Be sure the proper memory bank is
in use (LED is lit) for the call you wish
to place. If not, press the button next
to “Lower” LED until either “Upper”
or “Lower” LED is lit.
2. Press SPEAKERPHONE button to
get a dial tone. Speakerphone LED
lights to tell you the speakerphone is
in use.
3. Press the storage button next to the
name of the location you wish to call.
The number is dialed automatically.
You may continue using speakerphone
when your call goes through for hands-free
communication, or pick up the cordless
handset and press TALK for mobility.
To Dial A Number Stored In
Memory From the Handset
If you are away from the base where
the written directory is stored, you will
have to remember the directory storage
number for the call you wish to make.
1. Press TALK for dial tone.
2. Press MEMORY button.
3. Enter the directory storage number
(01-32) for the call you wish to make
(you must enter 0 before numbers 1-
9 in order to access the memory
number from the handset); the
number will be dialed automatically.
To Replace Or Change A
Number Stored In Memory
Simply repeat the steps under “To Store A
Number In Memory”. The new number will
automatically replace the previous number
stored. Be sure the red LED indicator is set
on the correct memory bank.
Permanent Memory Circuit
Your Cobra Intenna provides you with a
permanent memory circuit; even if you
disconnect the AC power or experience a
power outage, don’t worry-- your memory
bank will remain programmed
11
1-773-889-3087
NEED HELP?
CP-720
Cobra
®
USING THE MEMORY
DIALING FEATURE
1
2
3
LOWER
LED
SWITCH
BUTTON
UPPER
LED
1
2
3
LOWER
LED
SWITCH
BUTTON
UPPER
LED
4
SPEAKER-
PHONE
5
6
MEMORY
TALK
5
6
3
2
1