Filter
Top Products
ENGLISH
15
TROUBLESHOOTING Sony Ericsson
PROBLEMS
SOLUTIONS
The TT01 announces: "Bluetooth®
connection problem "
Switch off your telephone, then switch it back on
again if the TT01 cannot be operated .
Your telephone does not detect the
hands-free kit
Switch off your telephone, then switch it on
again. Check that the Bluetooth® connection of
your telephone is enabled.
Your telephone is not detected. Repeat the connection phase.
The person you are calling
complains of an echo during
communication.
Turn down the communication volume.
WARNING : refer to your Sony Ericsson telephone’s instructions if necessary
PAIRING PANASONIC X70
When you switch on for the first time or when you perform a new installation, you need to pair your telephone and your
TT01. Once this is done, connection between your telephone and your hands-free kit will take place automatically as soon
as the two devices are less than a few meters apart. A 'beep' will be heard, indicating that connection is established.
IMPORTANT : The hands free kit is only operative when the car ignition is on (IGN)
Procedure :
Switch on the telephone; turn on the ignition, the blue led shows that the hands free kit is supplied. Perform the following
sequence on the telephone. The first time you will hear the instruction ”PLEASE PAIR DEVICE”, otherwise reset the TT01
by pressing and holding the red/green buttons at the same time.
Switch on your phone, turn the key in the car ignition and two indicator lights on the keypad should light up to indicate your
hands-free is powered up. Now carry out the following sequence on your phone.
Access the main Menu and select “Organizer", press "Select". Go to “Connect” and press “Select” again. Enter
“Bluetooth®” then enter the “On/Off” menu.
Select “On” if it is not selected yet. Get back to the “Bluetooth®” menu by pressing
. Select “Discover & Pair” When the
search is over, select «TT01 CK3.xx». Press “Pair” to establish the connection. The display reads, "Bluetooth® passkey",
enter 1234 then " OK".
COMMUNICATING PANASONIC
The TT01’s green and red buttons are the main devices to make and receive calls.
Answering calls
:
• Press the TT01’s green button to answer the call.
•
Press the TT01’s red button to hang up at the end of a call or to reject a call.
Make a call in TOUCH & TALK mode:
• Briefly press the green button, wait for the tone, then say the name of the person you want to call.
E.g.: press green button, [beep], John..
• Press the red button to hang up.
Please refer to “MEMORIZATION of VOICE TAGS” section for name voice recognition.
Making a call manually
:
•
Use the phone keypad to dial the number. When the call gets through press the green button to switch to hands
free mode.
Managing Dual Calls
:
• A warning tone will alert you if someone is trying to get through while you are engaged on another phone call.
• Press green button once to communicate with a new caller.
•
Press green button once to return to your first caller.
• To end the present communication, press red button once.
ENGLISH
16
Discreet mode (PRIVATE)
:
• Press the green button briefly to switch the conversation to hands-free or handset mode.
To redial last number called (REPEAT)
:
• Press and hold the TT01’s green button.
Clearing memory (RESET)
:
• Use the TT01’s buttons. Press and hold the green and red buttons at the same time.
Adjusting the volume
:
• Use the keys on the handset to adjust the volume of the conversation.
WARNING: clearing the memory requires a new pairing phase.
MEMORIZATION OF VOICE TAGS PANASONIC
Your telephone allows you to associate voice tags to the names in the phone book. With the TT01, it is possible to use this
feature to recall names from the phone book by pressing the green button and repeating the name after the tone “beep”.
Procedure :
To use voice tags associated to names, you must activate voice recognition first.
To do so, enter the menu and select «Contacts list». Choose «Options» then «Enable/Disable». If it hasn’t been done
before, select «On».
To assign a voice tag to a name, enter the menu and select «Contacts list».
Enter the «Voice numbering» menu. Press «Menu», then «Add». Select the desired name and click on «Menu» then
«Recall». The following message is displayed: «Record your voice».
Then press «OK». «Voice numbering recorded» is displayed. Say the name. «Please record your voice again» is displayed.
Then press «OK».
«Voice numbering recorded» is displayed. Say the name again. «Validated voice numbering» to indicate that the tag has
been recorded. Otherwise the telephone will ask you to record your voice again.
To eliminate a voice tag associated to a name, access the «Contacts list » menu then «Voice numbering»
Select the desired name and click on «Menu».
Select «read», you can listen to the voice tag you have recorded.
You can delete it by selecting «Delete».
PAIRING MOTOROLA V500, V525, V600
When you switch on for the first time or when you perform a new installation, you need to pair your telephone and your
TT01. Once this is done, connection between your telephone and your hands-free kit will take place automatically as soon
as the two devices are less than a few meters apart. A 'beep' will be heard, indicating that connection is established.
IMPORTANT : The hands free kit is only operative when the car ignition is on (IGN)
Procedure :
Switch on the telephone; turn on the ignition, the blue led shows that the hands free kit is supplied. Perform the following
sequence on the telephone. The first time you will hear the instruction ”PLEASE PAIR DEVICE”, otherwise reset the TT01
by pressing and holding the red/green buttons at the same time.
Call up the “Configuration” menu then select “Connection”. Choose “Bluetooth® Link”, then “Hands-free”.
Now you need to search for your kit. Choose “Find Equipment” and wait. «TT01 CK3.xx». Answer Yes when prompted “Do
you want to couple your telephone and your kit?”. Enter 1234 in the Bluetooth® password entry screen and validate it.